The Replacement Standard Dual Rack Repair Kit for Lippert RV In-Wall Slide-Outs - Fixed Side, #LC84FR is the left side of the slide-out as looking at it, facing it, from the outside. The float side, #LC26VR, will of course be the right side as facing…
Hey Jack congrats on the new Jeep! To flat tow a 2021 Jeep Wrangler Rubicon behind your 2012 Thor Hurricane 31J motorhome, I recommend the following parts: Tow Bar and Safety Chains - etrailer XHD Non-Binding Tow Bar for Roadmaster Direct-Connect…
Hey Jared, the pass through amp rating of the Rich Solar NOVA 3K12 3000W 12V Pure Sine Wave Inverter with Built-in Transfer Switch for RVs #RS79VR is 30 amps. What AC units do you have? This should be more than enough for that.
Hey, Skip! Happy to help get your new Jeep set up for flat towing. There is going to be a list of parts, so I'll go ahead and list them all below for ya. Blue Ox Base Plate: Part #BX1139 Blue Ox Avail Non-Binding Tow Bar: Part #BX7420 Demco…
Hello Andrew, good question. Basically the only difference between the composite kits and the standard (non-composite) kits is the application they are used for. Composite are used in motorhomes, the other are used on towable campers. It has to do…
Hey Donna, you would have to replace the entire setup as there was a refrigerant law change in January of 2025 that forced the complete systems to have to be redesigned and because of that nothing is currently backwards compatible. So what I would…
Unfortunately, I cannot tell you what wiper seal you would need for your 2004 Keystone Outback. This is not something that is known just from the RV information. It depends on your particular slide-out. The best way to determine what wiper seal you…
You've got both a wiper seal and a bulb seal here with the wiper seals having a track for the bulb seal to slide onto. The Rubber Wiper Seal with Track for RV Slide Out #SR87FR you were already looking at is most likely the closest option to what…
In order to determine if the correct Lippert Replacement Hydraulic Cylinder like part #LC339031 you would need to measure the distance between your hydraulic fitting ports and note the color of the cylinder. The above Lippert Replacement Hydraulic…
Hey Kyle, yes the Flair-It High Pressure Hose #FL37FR does fit on the 1/2 barb fitting of the Flair-It PEXLock Female Elbow Fitting #FL44ZR that you also referenced.
Hey Henry! I would be happy to help you get your 2026 Jeep Wrangler ready for flat towing. You will need the tow bar, base plate, safety cables, wiring, and a supplemental brake system. I recommend the following: -Blue Ox Base Plate Kit - Removable…
Hey Gary! Your 2024 Grand Design Imagine XLS 25DBE came equipped with a Furrion 15,000 Btu air conditioner. That original model used R410A refrigerant and has since been discontinued, so a new unit won't be able to tie into the existing…
Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair.
Robert
Bloomington, IL
RV Slide Out Parts from JR Products
Get your slide moving again with JR Products parts built for straightforward replacements. Check the 1.85" x 1.20" cutout and a 40 amp rating, and know that 3-wire setups can work on multi-terminal switches with simple jumpers. If you're dealing with a unique 6-pin layout or need a bezel, plan to reuse the existing panel hardware.
Yes, JR Products 40 amp momentary slide-out switches can be used with Lippert slide-outs. Confirm your system does not exceed a 40 amp rating and that your panel cutout is 1.85" x 1.20". Check the pin layout; a 6-pin all-in-a-row style isn't offered, so verify your wiring style before ordering.
No, a dedicated bezel or mounting panel isn't provided. Plan to use your existing panel or a suitable opening sized 1.85" tall x 1.20" wide. If replacing a failed switch doesn't restore movement, inspect the motor next since a bad motor can mimic a switch issue.
Connect the trailer hot to Power (+), then the two motor leads to a Motor (+) and a Motor (-). Add jumpers between the two Motor (+) terminals and between the two Motor (-) terminals. There isn't a separate ground terminal on the switch. If wire colors are uncertain, identify them with a multimeter before hooking up.
They fit a 1.85" tall x 1.20" wide cutout and can be installed horizontally 1.85" wide x 1.20" tall. Measure your opening first; some OEM switches are much smaller like .75" x .65". If your panel is smaller, plan for a different mount or enlarging the cutout to avoid a loose fit.
Filters
