# 1
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Ball mount works perfect with my hitch. Great product!
Good product.. Only wish it came with the pin to hold it into the hitch
# 2
Curt Class III Ball Mount with 1-7/8" Ball - 4" Drop - 3,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
# 3
Curt Class III Drawbar - 2" Rise - 4" Drop - 13" Long - 7,500 lbs
Haven't used it yet. I bought it because of CURT's quality. It was beat up in shipping though.
Exactly what I needed to extend the reach of the ball beyond my rear tire carrier WITHOUT losing any tongue weight capacity! I used mine for the 2" rise.
# 4
etrailer 2-3/4" Rise or 4" Drop Ball Mount Kit - 7,500 lbs
Very good deal!!! And the quality is superb.
Nice kit for the money meets my trailer pulling needs.
# 5
B&W Heavy-Duty Ball Mount - 3" Rise, 4" Drop - 11-3/8" Long - 16,000 lbs
I had to flip this upside down and put a hitch ball on this to get it to work with my Dodge Journey and my camper. It's held up without issue for a half-dozen camper pulls. I wish the paint hadn't already started flaking off at the receiver end, but that's to be expected when you connect metal to metal. The other parts of this haven't started flaking yet after a year so hopefully it continues to hold up.
Really well built
# 6
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.
This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.
# 7
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Perfect fit on my car. I was worried I was going to have a hard time getting the right hitch and wiring harness, but thanks to etrailer, I didn't have a single hiccup. I was worried about not getting it in time for my cross country journey in which I will be needing to pull a small trailer. I ordered the hitch with only about a week before I'm supposed to start my drive and got everything within just a few days! Great all around. Really took the guesswork out of all of this. Thank you guys
I have purchased my trailer hitch, ball mount and hitch locks for my 2017 Dodge Journey. The service and products from this company have been top notch and I plan on using them in the future. Thanks again for a service that is increasingly hard to come by these days.
What our customers are saying:
"I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future."