# 1
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad - 4-Point Set
The system is not what was advertised, it's better, at least for me. Everything arrived on a pallet in excellent condition, except for the advertised remote. I contacted etrailer and they put a replacement on order which I received a few days later. In the meantime, I tried to place the controller in the mode to sync the remote and see if the remote I had with my RV would sync, but I could not get the controller in that mode to accept a remote. Upon reading the controller label, I noticed it said BT and had a passcode on the side of it, so I downloaded the app and it connected to my phone. It seems the LCI Linc remote is obsolete for my Ground Control 3.0 and it is now using the phone app. Everything seems to work as expected; I'm excited to try everything out this weekend on our first outing. I was able to push a fiberglass push stick from the front basement to where the rear jacks are located without dropping the underbelly and pull all the required cables to the rear of the camper and utilize existing frame holes to bring the connectors out to the rear jacks. I think this will be a nice upgrade to our fifth wheel after our factory landing gear failed.
shipped in a timely manner. Easy install wit good instructions. I did have one question about the location of the rear lifts and called the company and we had an answer instantly. Wiring was very easy with good instructions. The system worked on the first try and have had no issues so far. Great system. I was looking at newer campers with auto leveling and about 40 to $50,ooo if I traded my paid for camper in. The cost saved me a lot of money and works as it should and saves my back and a lot of set up time. would and have recommended to others. Thanks.
# 2
Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set
Let me say this to start, this system is AWESOME!! If you do not have a leveling system on your camper, this one works very , very well. I will say, the install and the learning curve takes time and is not too hard, but it's not super easy either. Once I got the system in place, and understood how to use it, the rest was a piece of cake. Take your time on the install and get help. The parts are robust and heavy, so two people make it much easier. Have sharp drill bits to drill the attachment holes. Wiring is super simple, but take your time and make sure you get all the connections good and tight and secured well with zip ties. The system requires a good strong battery, so make sure your battery is in great shape and you will not have any issues. Get the Lippert app also, it is very helpful. I love it now, when I pull my 2006 Keystone Raptor 5th wheel toy hauler into a campsite, I hit a couple buttons and the longest it has taken to level my unit is 2 minutes and 30 seconds. I love it! It puts the camper at the same level every single time, which is awesome. No guessing, no driving up and down on blocks, just push a button and walk away until the camper is perfect. Would I do this over again you ask? Absolutely. Awesome system!
After the initial installation there was a little confusion about setup I have been very happy with the way it works really simple push one button hit auto levels it's still working well thanks
# 3
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
The product itself was great. It fit right in to the brackets from our old landing gear. We were able to use our existing motor as a cross fit with this gear. The gear box was even better than Lipperts as it was not plastic. The only issue we had with this was shipping. We ordered the part same day as our water pump because we were told it was in stock. Low and behold they changed ship date numerous times, with the excuse it was not easy to pick. Anyhow, two weeks later we finally got the part we ordered.
I have a 2000 komfort 26FS. It has original landing gear that was made by Atwood.Parts to repair are apparently no longer available. Did alot of research and this kit seemed to be a good replacement. It is a exact replacement. Took some time to get it installed as my 5th wheel has a wall and frame right next to landing gear. Original motor bolted up with replacement of original screws which were half inch to short. Four days to get delivered to Oregon. I would have given a five star review but I was missing square tubing that runs from gear box to other leg. Tubing is clearly pictured in discription photos.
# 4
Landing Gear Set - 36-1/2" Lift - 8,000 lbs
Perfect replacement, works great, excellent shipping time and service. Just wish I had got the electric motor that goes with the legs.
Ordered this from etrailer instead of other sites as I knew the shipping would be faster. Sure enough I got the item in 4 days on Thursday and Installed it on Sunday. Very quick and easy. Took longer to get all my tools and set up items together than the actual work. The item was a exact fit with installation being feeding the legs through the holes in the floor down from the inside and installing the 4 clamping bolts to hold them in, the gear box on the lead leg and the cross bar and motor. Now it purrs like a kitten when activated instead of clanking and creaking and blowing fuses. Actual install time was probably 1.5 hours taking my time and injecting extra grease into the gears and lead screw. These replacement units have a grease fitting for both which is great and should allow them to last forever! Being a safety freak I used a 3 ton jack with a 4X6 placed long ways to catch the I beams under the trailer then placed 3 ton car jacks under the frame also and for extra safety backed my truck bed under the tongue for extra security while I worked. The price was crazy great, the fit was excellent and the shipping was fast as usual. less money in parts and 2 hours of work probably easily saved me a grand over taking it to a RV repair shop! Thanks etrailer. Saved me again!
# 5
Bulldog Tandem Landing Gear Set - Drop Leg - 36" Lift - 8,000 lbs
Delivery was on time, but the box it arrived in didn’t fair we’ll and parts were hanging out of the box! But everything was accounted for and the parts were well wrapped. Installation was very easy. The only issue was the locking pins mount plate is tack welded to the primary leg that the motor moves up and down. Those mounting plates had to be removed to install the lead and follow jacks. A grinder made short work of that. I didn’t put the mounting plates back on, instead I used my spring loaded pins that were on the old legs, they were still in good working condition. Also I didn’t use the adjustable cross over rod that came in the package . I opted to use the one that was on my old jacks, it was constructed of heaven gauge tubing and didn’t have a much (slop) movement in it. Also did not use the plastic housing gear box, I purchased a aluminum house gear box from e-trailer a few months back and used that one keeping the plastic for a spare. Very satisfied.
The leg pin came out because of the design, it is not a strong locking mechanism to not pull it all the way out. (My wife pulled it all the way out) Afyer furthet inspection, in addition to poor locking mechanism, the size of the pin is not adequate for the specified weight of the jack.
What our customers are saying:
"Easy place to shop. Fast delivery and great products. Very happy with my purchase."