Most Popular 500 lbs Vert Load for 2006 Nissan Pathfinder

I wanted a front mounted tow setup in order to make it easier to put my boat in a narrow garage and was getting ready to ask a guy to fabricate one for me. I remembered etrailer.com and was pleased to find the Draw-Tite brand receiver tow bar custom made for my Pathfinder. It was a "no brained". Very pleased!

etrailer--great communication and service. Prompt shipping. Product, 100%. Perfect fit and high quality. Install instructions were good... not the fault of etrailer or the product... but very hard to put a bolt into a nut that's been exposed to 10 years of the elements.

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Click to Enlarge

Click to Enlarge

I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

Click to Enlarge

Click to Enlarge

Click to Enlarge

Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

Click to Enlarge

Click to Enlarge

Click to Enlarge

VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )

Click to Enlarge

Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Very easy to install. works great for bike rack and generator box.

After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.

Click to Enlarge

It wasn't fun to install by myself, but managed to do it in a few hours. Worked out great so far, I've hauled motorcycles on hitch carrier for about 2k miles so far and had no problems.

Click to Enlarge

Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.

Click to Enlarge

I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?

How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Of the many hitch receivers I have purchased, the front mounted ones have never failed to surprise me of their usefulness! From bike racks, to carrier for coolers, to my chainsaws, gas and oil, they make it work. Recently while cutting wood for a hunting lease engagement, I put a second ball on the front and used it to drive a 16' trailer up a hill to get the wood where it was needed for offloading. Backing it up had resulting in damaged trucks, trailers and numerous attempts. Using the front hitch it was a one and done deal! Love it! I have even used it to pull trees over when felling. I don't have enough fingers and toes to count the uses! If you have ever thought about it, just stop and order! You won't regret it!

Click to Enlarge