# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Everything about my eTrailer experience has been absolutely first class, including the follow up emails, 2 of them. Due to a medical problem it's taken me over a year to complete the installation but that's on my end. I installed the hitch and wiring harness in May of 2016. I just now got to running the power wire up to the battery and finishing the job today, 8/2/17. Again, all due to issues on my end. The product, the personal assistance, and the videos made this job as easy as it could be for this 68 year old putting a hitch on a 2012 KIA Sedona by himself. Thanks to eTrailer for running a most excellent company in every regard.
Be aware that it is very difficult to get the nut on the ball tightened because it's hard to keep the whole thing from turning. Better to look for a receiver that has an indent machined where the base of the ball fits into the machined area to keep the ball from turning when tightening the nut.
# 2
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 3
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 4
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 5
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.
A nice solid constructed hitch. It should handle everything I hook up to
# 6
Buyers Products Ball Mount w/ 2" Ball - 3/4" Rise, 2" Drop - 8-1/2" Long - 5K
The hitch was delivered as ordered. The 2" ball was torqued on and it is a perfect fit to the receiver. Solid and high quality. etrailer.com has continued to be a great online retailer for me.
Paul/ you were a great help. Told me everything I needed to know. It works fine each time I use it. Thank you, Scott
# 7
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 8
Curt Ball Mount for 2" Hitches - 2-1/4" Rise, 3-1/2" Drop - 7,500 lbs - Chrome
Purchased because I wanted something that looked a little better than the standard black ball mount and couldn’t find the size I wanted in aluminum. I used it 3 times last season and put it away for the winter in my garage. It was never on the truck while salt was on the road. Pulled it out the other day and it is a disgusting rusty mess. Attempts to clean off the rust were unsuccessful it was that bad. Total waste of money BTW the picture is post cleaning, it was even worse before
My shipment came in on time and everything that I ordered was shipped correctly. All items were in great condition and not damaged. I am very happy with my order with etrailers. I will not hesitate to let anyone know where to purchase trailing equipment at a great price. Thank you so much for you help. I will install the hitch and all accessories next week and I will take pictures of the final install.
What our customers are saying:
"Very broad selection and outstanding service."