# 1
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 2
Curt Class II Drawbar - 3-1/8" Rise - 11-1/4" Long - 3,500 lbs
Used on my 1999 Dodge Intrepid's CURT 12006 Class II 1.25 in. Receiver Hitch: 350lbsTW/3500 lbs GTW. I use this Curt Class II Drawbar - 3-7/8" Rise - 11-1/4" Long - 3,500 lbs to tow a 3,500+ GTW dual axle trailer. I have used it with the trailer FULLY loaded and it performs EXCELLENT. You have to make sure the trailer is loaded correctly so as not to put too much down force on the tongue/drawbar. I was skeptical that the SOLID 1.25" bar would not take the load, but it is super strong. I chuck it in the trunk when not in use to protect passerby's shins, but it sticks out far enough clear the Intrepid's bumper, and is solid with a 2" ball (required a bushing). etrailer got it out fast at a good price! I would totally purchase this again from them.
Every part excellent quality. Perfect fit, all parts were exact for my vehicle. Watched the video on youtube for wiring and being a mechanic for over 50 years was able to connect signal lights all from driver side of harness. Instead of leaving plug inside trunk I wired through the rubber outlet to the back of the hitch ready for use. Very happy highly recommend etrailer.
# 3
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 3-1/8" Rise - 3,500 lbs
Service from eTrailer was great, they even wrote to ensure I got the order correct when I ordered a different size hitch cover than the drawbar that I ordered. Picture attached of the somewhat unique application for the Euro style setup I’m using – I’m dragging my race tires to racing events with my 750HP Cobra!
Excellent fitment and gives my trailer a level stance.
# 4
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
Works great. Just what I needed. Very heavy duty and should last a lifetime!!
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
# 5
Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
For Mazda CX-3 owners, this is the drawbar you need to achieve the correct final hitchball height for small U-Haul cargo or motorcycle trailers. You know the receiver sits quite low so this gets the height just where it needs to be, especially when the trailer is properly weighted/loaded.
Shipped in quicker than I thought it would. It fit it my old Hidden Hitch Class I receiver perfectly. I drive a '97 Geo Prizm, and the 5 inch rise is a definite plus in keeping my 5 x 8 utility trailer nice and level when I'm hauling lawn equipment. The only drawback is that the Curt drawbar does not come with the pin.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
What our customers are saying:
"Excellent service and communication. Expect part to be excellent too!"