# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
Hitch went on well, no missing or incorrect hardware. One bolt (RH front) was a little tricky, ended up pulling the bumper away a little to get it started, but not a big deal. Thickness of materials and welding are good. Had to notch the air dam plastic piece in three places, easily done with tin snips and a utility knife. Very happy overall. Tucks up in tight, doesn't hang down, not even noticeable. Now I have a winch mount, but even more importantly I have a really good pull point on the front, which these Cherokees lack. Would certainly recommend.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!
VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
Straight forward and perfect fit on my 2008 Toyota Tundra!!
# 7
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I'm off to overland in Texas and wanted you to know that the hitch and winch carrier are perfect. Using quick connectors, I can use ir on the front and rear. Removing it also saves on gas. It works great with a moulded number, saving on buying a specialized steel bumper and other expensive attachments. I like that I can still have all the internal mud guards and brush cover without having to take them off and not be able to have them on. Awesome!
This is a high quality hitch that fits the Gladiator perfectly. The hardest part of the installation was removing and reinstalling the push fasteners on the plastic air dam. While the hitch fit is perfect, the instructions for cutting the plastic air dam leave something to be desired. I finally had to eyeball the location for the hole and then found that the suggested utility knife simply wouldn't cut the plastic air dam. An oscillating saw solved the cutting problem easily and the best guess location worked out. Am I happy with the end result? You bet! Would I do it again? Absolutely.
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.
Great product! Fit perfectly on my 2005 F350. Instructions were easy to follow and it's possible to do it singlehandedly. Thanks trailer!
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
Detailed information provided to ensure correct selection of equipment for my pickup. Great support service. Quick delivery with updates available along the way. Installation was as advertised. No surprises..
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"