It appears that the HydraStar Disc Brake Kit # HSE7K-T1 is the correct kit for your 2021 Vanleigh Vilano 320GK. To verify this you can find the axle serial numbers and send that information to me so I can verify all the components are correct. Otherwise you can disassemble one of your hubs to verify your spindle measurements.
This kit uses
Inner bearing # 25580 (inner diameter 1.750")
Outer bearing # 14125A (inner diameter 1.250)
Grease Seal # GS-2250DL (inner diameter 2.250")
Wheel... view full answer...
Unfortunately, Hollywood Racks doesn't have a rack that has an integrated ramp that's also rated for 5th wheels. So instead, I recommend going with the Yakima OnRamp LX Bike Rack for 2 Electric Bikes # Y88DJ.
This rack has an integrated loading ramp, a 80 lb per bike capacity for a total of 160 lbs, and will work great with 5th wheels. view full answer...
Hey Anthony, the Dexter hoses like the part # T4890700 and the Kodiak hoses are about the same in quality. I would not put one over the other and I know the hoses you have now will work just fine. Both are considered to be on the higher end of quality for brake lines. How'd the install go? view full answer...
Definitely a smart idea to replace your Atwood heater with a tankless unit, as they are much more energy-efficient and quicker to heat your water. We do have an option that will easily fit in place of your 16" x 15-1/2" x 20-7/8" Atwood GC10A-4E, which is a unit from Furrion, and it will require the correct size access door as well:
- Furrion RV Tankless Water Heater # FR93FR
- Access Door for Furrion RV Tankless Water Heater - 18" x 18" # FR73FR
Th Furrion measures 19-3/16" deep x 12-5/8"... view full answer...
Yes - the Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches # HLY64FR is the same as model HR1700. We here at etrailer usually have different part numbers than the bike rack manufacturer.
With the ladder at the middle of your 2022 Grand Design Reflection 341RDS, there is a way to know for sure if the rack does not interfere with the RV Rider when folded up. The measurement you need to conduct is from the center of your hitch pin hole to the furthest outward point of... view full answer...
Hey Pedro!
Ultimately, you'll be looking to make sure the 4500 Series Converter # PD4575CSV has an output of 13.2 and 14.4 Volts DC (14.6V for a Lithium setup), but there are a number of steps to get to this point which you can find here - https://www.progressivedyn.com/wp-content/uploads/2017/05/PD4500-SERIES-TROUBLESHOOTING.pdf
I would copy and paste it all in this answer page, but this is directly from the Progressive Dynamics website so I'd want to make sure you're getting the info... view full answer...
Hi Jake; the Furrion Chill HE Replacement RV Air Conditioner for Coleman Setup # FR32PV is an old kit that is on its way out. We no longer recommend replacing just the AC unit, and can't guarantee this will work as a plug and play replacement.
We have had customers in the past successfully swap them out, others have found the connector doesn't work, sometimes the systems don't work together, and occasionally mixing up the AC with other components burns out the air distribution box (ADB).... view full answer...
Hello Brian, thanks for reaching out. Our records show the Lippert V000448334 is a standard 7,000 lb axle that uses the # 25580 (1.75" ID) inner bearing and 02475 (1.25" ID) outer bearing. I do suggest you remove a hub and confirm this is what you have. If so, the hub you need is the following:
- Easy Grease Trailer Hub and Drum Assembly for 5.2K - 7K Axles - 12" - 8 on 6.5 - Pre-Greased # AKHD-865-7-2-EZ-K
This hub uses 1/2" studs. I was not able to find a reference for your axle part... view full answer...
Hello Andrew, thanks for reaching out. We should have the seal you need, but there is no way for us to use your VIN to know exactly what seal you have. RV manufacturers just do not list this kind of information online.
Your best option will be to remove a wheel and look for a part number cast on your hub. Brake drums will have a part number on the front and we can typically use this to know your seal size and bearing information.
The only other way to know you seal size would be to remove... view full answer...
Hey Daniel, is it a Solera brand awning? If so, and yours measures 69 inches we do have replacement support arms with the part # LC281154 for black or part # LC281152 for white. When you get a email me the pictures if you are still not sure and I'll see if I can ID what you have/need. view full answer...
Hey Daniel, it sounds like you are looking for the Replacement Manual Override Grommet for Solera Powered RV Awnings # LC95ED which is what you have to remove to operate the awning manually. Did you lose yours? view full answer...
I'm sure we can get you a hub and drum assembly for your trailer but there's quite a bit of info needed in order to do so. To find the correct hubs you will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly on them.
If you are unable to find them, you need to use a digital caliper and measure your spindle where the bearings and grease seal ride, like in the diagram I added... view full answer...
To replace your Coleman Mach AC unit, I recommend the Advent Air Replacement RV Air Conditioner for Coleman Setup 15,000 Btu - White item # ACCOL150 or item # ACCOL150B in black. I do not have a heat pump for you. None of our replacement AC's for Coleman Mach set ups come with a heat pump or have an add on option like the Coleman 48004-066 which we do not carry.
You can add a heat strip with the Electric Heat Strip for Advent Air RV Air Conditioners item # ACMHD.
These units come with... view full answer...
Since you have 8K 3" axles you'll just need the Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3" Trailer Axles # RM-2460-2580.
The 3-1/2" requirement you were getting with the # RM-2470-2580 was simply because of the shock kit. I do recommend replacing your U-Bolts as well though with ones like # APUBR-9 as these get stretched and worn out after being torqued down and could potentially cause an issue down the road. These U-Bolts fit a 3" axle with 1-3/4" or... view full answer...
The number of leaves on a leaf spring is not the only determining factory in the amount of weight it can handle. The thickness of each leaf as well as what the leaf is made out of can affect the weight rating and performance of the spring.
The Roadmaster Comfort Ride Leaf Spring Suspension Kit # RM-2460-2570 does use 5 leaves that are 3/8" thick. Each spring is rated for 3,500lbs which is 7,000lbs per axle. This kit upgrades your suspension by allowing the axles to act independently of... view full answer...
Yes there is! You can get exactly that - a Roadmaster Comfort Ride system with shocks for your 8,000 lb axles that are 3 inches in diameter. What you need is the following:
- Roadmaster Comfort Ride Leaf Spring Suspension Kit w/ Shocks - Tandem 8K, 3" Trailer Axles # RM-2460-2580
The # RM-2460-2580 is a combination of the 2580 slipper springs that have the capacity you need for your 8,000 lb axles and the 2460 shocks that fit 3" diameter axles.
You made a really smart choice going with... view full answer...
There's multiple options for a gooseneck pin box and I will need to know which one your Vanleigh Beacon 5th wheel trailer currently has. If you could email me back a picture of the sticker on your trailer's pin box I will be able to find out which one you need.
The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item # GY48GR you were looking at is a replacement option for the Lippert Turning Point. This isn't a common pin box but if you have a Lippert Turning Point this is... view full answer...
Thank you for providing those pictures, using the pictures I was able to determine that the Replacement Touch Screen Control Panel # LC83VR is the correct replacement for your Lippert jack system. view full answer...
Hi Gayle; the only rack we carry for an e-bike and e-trike is the Hollywood Racks Sport Rider SE Bike Rack for 1 Electric Trike and 1 Electric Bike # HLY87RR. However, this is only rated for passenger vehicles and motorhomes. I'm sorry to say I don't know of a bike rack that can carry both and is 5th wheel rated. view full answer...
I took a look at what Lippert and ourselves offer as replacements for the Lippert Solera awning, and the outer cover for the arm that you mentioned is actually offered as a replacement part.
Instead, to replace that piece, you're going to have to replace the entire arm assembly with something like the:
-Solera 69" Standard Flat Awning Support Arm # LC281154 which will work with power and manual awnings, and measures 69" in length.
If you can let me know what size you need, I'll be happy... view full answer...
Go To Results