Finding information on the Tie Down 46250 was not an easy task as it was discontinued awhile back. From what I could find, it looks like the calipers marked 46250 often times have to change the mounting bracket and rotor/hub in addition to the calipers. This means the DeeMaxx Disc Brake Caliper # DE86VR would not be an exact replacement and likely not compatible.
Your best option is going to be a full replacement like the Kodiak Disc Brake Kit part # K2R35D if you have a 3,500 lb. axle... view full answer...
There isn't a harness similar to # 118247 that fits your 2005 Ford Expedition with 4-Way connector but I do have a solution that will allow you to add a 7-Way fairly easily and retain the use of the 4-Way as well.
You will need connector # 37185. The 4-Way you have will plug into this adapter. The white wire grounds to the vehicle frame. The other wires will connect to tow package wiring under the vehicle. Follow your 4-Way forward under the vehicle to where it connects to another harness.... view full answer...
The Curt MV Weight Distribution System part # C17062 is composed of the following parts:
Curt Spring Bar Retainer Package for Round Bar Style Weight Distribution part # 17109
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000 lbs part # A-6
Replacement Lift Handle for Curt Weight Distribution Systems part # C17112
Replacement Lift Bracket for Curt Weight Distribution Systems part # C17008
Replacement Bolt Kit for Curt MV Weight Distribution Systems part # C17076
Curt... view full answer...
For your 2020 Ford Expedition the SumoSprings kit part # CSS-1168 is the best solution for rear suspension enhancement. This will work great with your weight distribution setup as well. view full answer...
You are correct. The Lippert Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059 is the correct kit for your Venture VMC900 landing gear. view full answer...
According to my contact at Blue Ox, the # BLU34FR is the XL fang that you're looking for so you'll want to use this on your 2017 Ford Expedition. This can be used with any Blue Ox Patriot braking system like the Patriot # BLU37TR system to adapt to the larger pedal on your vehicle. view full answer...
Yes, Lippert 18:1 Venture Actuator Slide-Out Motor Item # LC132682 will work as a replacement if your motor is a Venture through-frame slide-out motor. view full answer...
We've found that approaching a brake controller install on a 2017 Ford Expedition with a factory 4-way is easiest if you just convert the 4-way to a 7-way with the part # ETBC7 since accessing the wiring that is only sometimes present on your vehicle for wiring a brake controller is pretty difficult to find.
So you'd want a brake controller like our best selling and performing P3 part # 90195 and the # 22292 to power and provide the brake signal and then you'd use the wiring of the # ETBC7... view full answer...
The Yakima Sweetroll Kayak Carrier # Y04074 does not come with lock cores but you can add them with the Yakima Same Key System (SKS) Lock Cores # Y07204 (pack of 4). If you just need a single lock core replaced and it has A137 stamped on the body of the core, you can use the # Y8771-A137 as a replacement that will work with your current keys.
If you've got a different number stamped on the lock cores or your existing key, let me know what number you've got and I can help you locate the... view full answer...
For a 1999 Ford Expedition with factory-installed 7-way the replacement connector is part # A10-7072VP. For a combination 4-pole/7-way instead you could use # HM40975. Both connect with a round U.S. Car Connector like the one shown in the linked photo.
If the Expedition has no factory trailer wiring you can still have a 7-way. You will start with the plug-and-play 4-pole kit # 118344 which installs at your tail light connectors with no cutting or splicing. If you need only basic lighting... view full answer...
Minor corrosion can be addressed with cleaning and coating the pin to prevent further issue but if your pin is bent I suggest you replace it.
As for the useable life of a hitch pin, that cannot be established due to too many variable such as environmental conditions, and use during time frame. To put a definitive length of time toward usability is difficult however, if you have damage in any way, including bending, I would immediately replace before it possibly fails.
We have a wide... view full answer...
If you are looking to replace the core for your Thule Terrapin cargo box, I absolutely recommend going with the # THLOCKN008 lock core. This will be a direct replacement, double check to make sure it is a different core number, and will fit your cargo box without issues. You will also need the # THKEYN008 key and # 853-1251 change key to remove the old core and secure the new one in place. I always recommend more than one key, just in case. view full answer...
We have a thin foam gasket that you could use, # AMG-FM. with a 2 inch hitch cover. They are thinner than the gasket that came with hitch cover # CR-007 so you may need more than 3. view full answer...
For a 2 inch square axle you are going to want u-bolt plate # TRTP200175. The hole spacing on center is 2-5/8 inches by 2-3/8 inches. For matching u-bolts go with # SP01-160. They have a 9/16 inch diameter.
I have included a link to a video review for you for the u-bolts. view full answer...
To replace the brackets on a Fastway e2 # FA94-00-1000 with round bars you will need the following parts:
Replacement Outer Link Plate for Fastway e2 Sway-Control Bracket # FA93-02-5350
Replacement Inner Link Plate for Fastway e2 Sway-Control Bracket # FA93-02-5200
Replacement Hardware Kit for Fastway Sway Control Brackets # FA92-02-9200 or bolt only with the Replacement Bolt for Fastway e2 Sway-Control Bracket # FA93-02-9270
Replacement Sway-Control L-Bracket for Fastway e2 Weight... view full answer...
One of the components needed to install a brake controller in your 1999 Ford Expedition is the part # 37185 that you referenced. You would also need a brake controller and install harness.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller that senses the amount of braking the tow vehicle is applying and applies... view full answer...
Yes, for the Electric Jack w/ Footplate # EJ-3520-BBX, we do have the Replacement Light Board for etrailer Electric Jack # EJ-3520-LT. view full answer...
The Aries Grille Guard - 1 Piece - Black Powder Coated Steel # AA3060 or the stainless steel 3060-2 you referenced will use bracket # AABRKT-3060. This is a custom fit for 2007-2015 Ford Expedition models and that specific grille guard. view full answer...
Using spring bars that are rated for a higher capacity can lead to a rigid trailer ride. An over-rated weight rating on your spring bars can even cause bounce leading to traction issues with the trailer.
I definitely recommend getting the spring bars that are rated for your specific trailer and vehicle using the total tongue weight. The total tongue weight is the loaded trailer tongue weight along with any cargo weight behind the rear axle of the tow vehicle. That weight combination... view full answer...
I would love to help but I spoke with my contact at Pro Series and they informed me that the replacement spring bars you are inquiring about have been obsolete for quite some time which means replacements are no longer available. Unfortunately, the only option I have for you would be to switch to a new system. For this, we have the Reese Weight Distribution System part # RP66131 without sway control or the Reese Weight Distribution System part # RP66130 with sway control which are both... view full answer...
Go To Results