To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Most hard covers limit what you can haul, but this hybrid design rolls up in seconds to give you full bed access. The TruXedo Sentry combines 3/4" thick aluminum slats with a premium 5-layer polyester and vinyl top for strength and flexibility. Safety straps secure the rolled cover at the cab so it stays out of the way and doesn’t block your rear window. Quick-release guides let you remove the cover completely without tools when you need the bed completely open.



Rain, snow, or sun won’t slow this cover down. The industrial-strength, leather-grain vinyl over heavy-duty aluminum slats is resistant to UV rays and harsh conditions from -40°F to 120°F. The fabric keeps its clean look better than standard vinyl, while the black aluminum slats add impact resistance and a seamless, fully “blacked-out” look when rolled up. With a 400-lb evenly distributed weight capacity, you get real protection without giving up usability.

This cover sits just 1/2" above the bed rails for a smooth, flush appearance. The angled 15-degree side rails cut down on wind drag and noise while helping improve fuel economy. Because the rails mount inside the bed, you keep easy access to stake pockets, tie-downs, and other accessories. The self-leveling design keeps the rails square so the cover rolls smoothly and seals tight every time.

Security is built right in. Slam latches at the tailgate and additional latches at the mid-bed lock automatically to keep your gear safe. When the tailgate is closed and locked, the cover locks with it to create a secure, sealed bed. Rubber weather seals along the edges help keep out water and dust, so what’s inside stays clean and dry.



Getting this cover set up is straightforward thanks to the clamp-on mounting system. The bolt-on clamps secure the rails inside the bed without drilling, leaving the stake pockets open for accessories. Built-in lips keep everything level as you tighten the clamps, so the cover rolls and seals evenly from day one.


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.












Allan
5/17/2025
Cover is holding up great. Gets everything dry in the bed of my truck. If you are thinking of buying one, just do it. Great product