To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you need the whole bed to load up tall or bulky gear, the Sentry rolls up in seconds without tools. Just release the tailgate latches and roll it toward the cab—safety straps hold it tight so it won’t move while you drive. The 3/4" thick aluminum slats under the vinyl top make it strong enough to protect your cargo yet flexible enough to roll up compactly, keeping your rear window and brake light clear.


Rain, dust, and sun don’t stand a chance against this hybrid cover. The industrial-strength, leather-grain vinyl fabric is pressure bonded to heavy-duty aluminum slats and backed by rubber weather seals that keep water and dust out of the bed. Tested to handle temperatures from -40°F to 120°F, the 5-layer polyester and vinyl surface resists UV damage and stays clean longer than standard vinyl covers.

For a sleek look that doesn’t spoil your truck’s lines, the Sentry mounts on 15-degree-angled side rails and sits just 1/2" above the bed rails. This flush fit reduces wind drag and helps improve fuel economy. The all-black aluminum slats and fabric top give it a uniform matte finish that blends in cleanly whether rolled out or stored.

Security is built in from front to back. Dual slam latches at the tailgate lock down automatically when you press the corners closed, and additional mid-bed latches engage at the same time. Used with a locked tailgate, these points keep thieves from prying up the cover or reaching underneath. The hard aluminum slats add another layer of strength for peace of mind when you leave gear in the bed.


Setting up the Sentry doesn’t require drilling or measuring tricks. Bolt-on clamps attach the side rails inside the bed, leaving stake pockets free for accessories. Built-in self-leveling lips keep the rails square as you tighten them so the cover rolls evenly every time. When you need to take it off completely, the quick-release guides let you remove it in seconds without tools.




Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.











Allan
5/17/2025
Cover is holding up great. Gets everything dry in the bed of my truck. If you are thinking of buying one, just do it. Great product