To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
A lot of hard covers make you choose between strength and convenience, but this one gives you both. The TruXedo Sentry uses 3/4" thick aluminum slats wrapped in a premium, 5-layer woven polyester and vinyl fabric. You can roll the whole cover up in seconds and secure it at the cab with built-in safety straps, so hauling tall or oversized cargo is simple. When you need to remove it completely, the quick-release guides let you take it off without tools.


The rails angle at 15 degrees so the cover sits just 1/2" above the bed for a clean, low-profile fit. That flush design cuts down on wind noise and drag, helping improve fuel economy while keeping the truck’s lines smooth. The inside-mount rails leave your stake pockets free for tie-downs or other accessories.

This hybrid build handles everything from blazing heat to freezing temps. The 5-layer polyester and vinyl fabric has been tested from -40°F to 120°F and shrugs off UV rays, dirt, and rain. Underneath, the 3/4" thick aluminum slats protect against impacts and can support up to 400 lbs of evenly distributed weight when closed. Rubber weather seals around the edges keep out water and dust, so your gear stays protected in bad weather.

When the cover’s closed, it locks automatically at the tailgate with dual slam latches. Additional security latches at the mid-bed lock in place at the same time, so no crawling under the cover to secure it. With the tailgate locked, the bed stays sealed and secure against theft or prying hands.


Installation is straightforward with bolt-on clamps that require no drilling. The self-leveling side rails square themselves as you tighten them, making setup easy and ensuring the cover rolls smoothly every time. Hook-and-loop fasteners keep the edges tight, and because the rails mount inside the bed, most bed liners, caps, and rails remain compatible.




Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.











Allan
5/17/2025
Cover is holding up great. Gets everything dry in the bed of my truck. If you are thinking of buying one, just do it. Great product