To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you need the full bed open for hauling larger items, the Sentry makes it easy. The 3/4" thick aluminum slats roll up together with the vinyl top layer in seconds, and built-in safety straps hold the cover securely at the cab. It rolls compactly—about an 8" diameter—so it won’t block your rear window or third brake light. You can even remove it completely without tools thanks to quick-release guides.



If you care about keeping your gear protected, this cover’s hard aluminum slats and slam latches do the job. The slats are impact resistant and can support up to 400 lbs of evenly distributed weight when closed. At the tailgate, dual slam latches lock automatically, and mid-bed security latches add another layer of protection against prying. When used with a locked tailgate, the bed stays fully secured.



The side rails are angled 15 degrees so the cover sits just 1/2" above the bed for a flush, streamlined look. Rubber weather seals run along the edges to keep out water and dust, while the aerodynamic profile helps cut wind drag and can even improve fuel economy. With the cover closed, the blacked-out aluminum and vinyl finish looks sharp and performs through every season.

The premium fabric top is bonded over heavy aluminum slats for strength and durability. It’s a 5-layer woven polyester and vinyl blend that resists UV rays, dirt, and harsh weather, keeping its clean look even after long exposure. Tested to handle temperatures from -40°F to 120°F, it stays flexible and tight in both heat and cold.

Installation is simple with the self-leveling side rails. As you tighten the bolt-on clamps, the rails square up automatically with the bed, making the cover roll out smooth and even every time. Because the rails mount inside the bed, you still have full use of stake pockets, bed liners, and rail-mounted accessories.


Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.















Allan
5/17/2025
Cover is holding up great. Gets everything dry in the bed of my truck. If you are thinking of buying one, just do it. Great product