To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Retractable tonneau for your vehicle has aluminum slats and a vinyl top layer that combine the strength and security of a hard cover and seamless look of a soft cover. It locks at any point along the rails, and it retracts easily with a handle.
Features:
Specs:
Retractable Cover with Built-In Pull Strap
The original JackRabbit retracts with the turn of a handle. The handle - located on the key latch at the tailgate end of the cover - activates a heavy-duty tension spring. This spring automatically retracts the cover into the canister at the bulkhead of your truck bed. A built-in pull strap helps you extend the cover over your bed. As you pull, the tonneau will engage the side rails at 12" intervals. You can stop the cover at these designated intervals or you can use the key latch to lock the cover at any point along the side rails.
This feature enables you to carry tall or long items that overlap your tailgate while still covering cargo, such as a toolbox, stored closer to the bulkhead of the truck.
A hook-and-loop fastener strip is included to secure the pull strap up and off of your bed floor. You can also use the rear plate of the tonneau cover to pull it closed.
Angled Canister
The cover retracts into a compact, angled canister located at the front of your truck bed. This canister protects the retracted cover from the elements, and with the cover stored in the canister you'll have unrestricted visibility out of your rear window. The angled design of the canister also allows for maximum clearance for your tools and cargo so there is no need to remove the cover to haul cargo.
Water Management System
The JackRabbit rails feature a water management system that channels excess water into the canister. This prevents water from getting into your bed or freezing in your tonneau cover rails during cold temperatures. Drain tubes attached to the bottom of the canister remove water through the OE drain holes in the floor of your truck bed.
Flush-Mount Design
The black powder-coated side rails mount level with your truck bed rails for a flush appearance. This flush-mount design is aerodynamic to reduce wind drag, and it helps to improve gas mileage when the cover is closed.
Even with the flush-mount design, the cover fits over most fifth-wheel trailer hitches. Note: The highest point of the fifth-wheel hitch must be at least 2" below the bed rails.
Stylish and Heavy-Duty Construction
The JackRabbit deck is constructed of a vinyl top layer bonded to heavy-duty aluminum slats. This ArmorTek deck looks like a soft tonneau cover with no visible seams, but has the strength and security of a hard tonneau cover. A large seal at the rear of the bed closes the gap between the cover and tailgate to create a barrier to prevent water from entering the truck bed.
Security
The Jackrabbit provides excellent protection for your cargo when used in conjunction with a closed and locked tailgate. The heavy-gauge aluminum panels are better at preventing theft when compared with soft covers that can be cut or punctured with a knife. The panels are also more effective at preventing theft than tri-fold hard tonneau covers because the panels cannot be pried open at any point along the rails.
No-Drill Installation
To install the cover, set the canister in your truck bed and support it with a box or other sturdy object. Slide the cover side rails into the canister until they are fully seated in the rail grips while also threading the cover into the channels in the rails. Secure the rails to the canister with bolts and washers.
Secure the rails to your truck bed side rails using 2 clamps per side. Slide the clamp onto the rail, flip the pivot arm up so it is under the bed rail lip, and tighten the clamp in place. Shims are included for trucks with tapered beds.
Mount the top cover plate to the canister with the included hardware. Attach the drain tubes to the canister and route each tube out of the OEM drain holes in the floor of your bed.
To hold the pull strap off the floor of your truck bed, apply the adhesive hook-and-loop fastener strip onto the underside of a rail at your desired location.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we are going to be taking a look at the Pace Edwards line of Jackrabbit Tonneau covers. The Pace Edwards Jackrabbit is a great way to protect your truck bed and your gear. It's made with Armor Tech padding that's laminated to aluminum ridged panels so it gives you hard cover security with a soft cover look. It's easy to operate. It features a one latch release system. We'll drop down our tailgate, we'll be sure and hold on to our pull strap, turn the latch to the left, and the tension springs roll it up for us.
It has multiple catches along the rails. This is great for partial loads. The rear plate doubles as a handle and it can be locked in any position, two keys are included.When used in conjunction with a locking tailgate, the whole bed is secure. It's a no-drill application. The rails easily clamp on in place.
The clamps themselves have a unique two-piece rail design, which allows them to fit tighter than your traditional style clamps. The whole thing has a flush-mounted low-profile design. The canister sits inside your truck bed, about 11 and a half inches. The rails sit inside your truck bed, about two inches. It features a large tailgate seal that sandwiches between to prevent water from getting inside.
The whole thing is weather resistant and since it is made out of aluminum, it's going to resist rust and corrosion. That's going to complete our look at the Pace Edwards line of Jackrabbit Tonneau covers.
Ratings & Reviews
Like the idea very much.
It leaks near the tailgate and the drainage tubes all ways come undone so it leaks real bad at the back of the of bed as well.
Would recommend if your not loading up the bed like a contractor.
Just received my q25 hitch, one end of the box was missing and the other was torn up pretty bad, the two side pieces are scratched up a little, I'll touch them up with some black paint, other than that it looks like it will work good.
4 stars, good quality product and packaging. Installed by myself in 1 hour. Fit and finish are very high quality.
However...the drain hoses for the canister are both 3" too short to reach the drain holes in the bed. And even if they were long enough, the hoses are too big to fit through the drain holes. So now I have to bodge together some sort of clamped-on extension so the canister drains properly.
Easy install and great quality
The Jack Rabbit is a great Tonneau cover. It looks great and the installation process is pretty straight forward. I like the fact that it is very low profile. It provides the security of a hard cover but is very easy to retract and get out of the way for hauling.
Looks great. Protects items stored in the bed. Opens up to use fifth wheel hitch. Just what we needed. That's the positive side. It took a long time to get it. It was quite a bit of work to install it. But it does fit well and it appears to be excellent.
Excellent fit on my step side. Recommend dry fitting on the floor before installing on the pickup.
RECEIVED THE COVER IN A TIMELY FASHION, OPEN MAIN BOX AND NO DAMAGE , SLID THE RAILS OUT OF THE CARDBOARD , THEY WERE WRAPPED IN PLASTIC THEY LOOKED FINE BUT A FEW DAYS LATER WHEN i STARTED THE INSTALL THE RIGHT RAIL AND A MAJOR BLEMISH ON THE INSIDE RAIL. DURING INSTALL HAD A MAJOR PROBLEM INSTALLING TH RIGHT RAIL WOULD NOT SLIDE ONTO THE BOX WITH THE COVER VERY EASILY TOOK ABOUT HALF HOUR TO FINALLY SLIDEING IT ON. WHEN I WENT TO INSTAL THE REAR RIGHT SIDE RAIL THE CLAMP WOULD NOT SLIDE INTO THE GROOVE AT ALL. HAD TO JUST HAVE IT SLIDE ABOUT A 1/2" INTO THE SLOT BUT THEN THE LEVELING RAIL SCREW WOULDNT WORK BECAUSE THE CLAMP WASN'T GOING INTO THE SLOT IN THE PROPER PLACE. THE RIGHT RAIL WASN'T MANUFACTURED VERY WELL AT ALL. ALSO THE TOP COVER OF THE BOX WHICH WAS WRAPPED VERY WELL BUT THE TOP RIGHT SIDE FINISH WAS NOT IN GOOD CONDITION HAD A FADED LOOK TO IT.
Had a small cut in the vinyl but I didn't have time to return it. Instructions are basically near ridiculous. I had to reread 5 times and photos are worthless. Ultimately it's installed and working as advertised. Kinda of expensive.
On a 2009 GMC Sierra 3500 HD it was a straight forward installation. 2 people a few hours. The old cover was shot. I'm very pleased with this cover, as it opens/closes and latches easily.
Cover works as advertised and it’s a great option for a long bed truck with a fifth wheel hitch. Going to order a second cover for my wife’s truck.
The included instructions are lame so make sure you watch the etrailer install videos. They are so
Much better and answer most of the questions.
Great product!! Installation was pretty easy. Attaching the side rails were a little tricky at first, but once you figure out how they attach, pretty easy from there. Looks good on my Chevy 2500 HD! Highly recommend it!
product arrrived when it was suspossed too. Works good. Had to partially redo the install has one side was stuck. got it to work fine.
I just love the Tonneau cover! It was easy to install and keeps everything dry and clean. My son and grandson are jealous and want one for their pickups.
The directions seem attempted but, not updated or clear at all. The screws and bold threads were cheap, strip out easy. It looks sharp but, if a tight seal is needed, this is not it at all. It is for “locking/hiding items, monsoon or snow main protection but, stuff is going to get wet 100%. For a product of the caliber and cost, these types of things create doubt in a product and longevity.
Great service from etrailer! Was backordered, they kept me updated well. When it came in, I was headed out of town so ONE call placed it on hold until I returned. It was queued up to ship when I returned, and that is exactly what happened. I missed the notes in reviews about the video, so I went with the paper. Did a little figuring-out and got it installed, but one side would not roll out. Cant see the mechanics of it in the cannister, so I called Pace-Edwards. They connected me with an engineer who correctly diagnosed the problem, sent the needed part, told me the procedure to effect the corrections, and it is now the best top I've had (and there have been many...). So, the shims that are on the clamps are on the clamps already installed on the rail, not the ones you install. And you need to be sure both sides of the mat are in front of the guide before you install the rails. If you read this review, the take-away is watch the video, heed the advice, and yes, the new tow-beast DOES fit in the garage. If only just...
Have not installed it yet but I am very happy with the one I had on my ram truck and will be installing this one on my Ford this weekend
This is the second Pace Edwards Tonneau cover I’ve owned. My first was on my 2021 Ram and the second went on my 2024 Chevrolet 3500 High Country. Both cover have worked flawlessly and I have no regrets purchasing these two covers.
The bed cover is great. The instructions not to much. They were quite confusing. And the Allen key and socket/wrench sizes in the tools required section were not the correct sizing.
I did the whole install in around 2.5 hours all by myself. It’s doable, but would be much much easier with a second person.
Had to use parts from my old retractable cover to complete the project .
I like the look and fit, getting the rails to slide in to the canister was a little challenging - but over all it works well. I will say the clamps have grooves in them to slide in for locking - I had a really hard time getting those to slide into place.
I was really disappointed in this cover. I've had retractable ones on other trucks and this one is cheaper than ones I've had in the past. It has a plastic drum where as better ones are made of stainless steel. The locking mechanize is really difficult to turn and I have already had problems with it. The installation directions are useless.
I would not recommend this cover. If it wasn't so heavy I would have returned it.
I like it much better than my old Flip Pac. It seems about as sturdy as the Flip Pac as well, I anticipated it would be more rigid, but that was only my perception so I did not knock a star off. Very easy to use. The instructions need an update, it looks as though they are now doing a step during assembly. Would have been much easier to install with a second person, like stated in the instructions, but I did manage by myself. Realy like the look and fitment, haven't tested the water tightness yet.
Just installed but so far,I love it. Had difficulty installing the side rails while it was sitting on the box in the bed. Tried 3 times and couldn't get it. Took everything out of the bed, placed it on the ground, rotated 90 degrees. This way the rails were installed vertically. Fell into place. Obviously, this way took an additional person, but it worked.
Not as easily done by yourself but doable though. Took me about a hour. Looks great. Had questions about the bedcovers on top edge, to leave or remove. See pics. For some reason it was a little snug at backend of truck bed.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.