To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
These premium mud flaps are easy to install and digitally designed to fit your car or truck. Protect your vehicle and your trailer from road debris. Flaps are constructed of durable thermoplastic resin with stainless steel fasteners.
Features:
Precision fit, durable components and ease of installation make WeatherTech NoDrills your first choice in mud flaps. Installing mud flaps has never been this painless. Patent-pending QuickTurn stainless steel fasteners makes installation quick and easy - no drilling required.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2018 Ford Expedition, we're gonna be taking a look at and showing you how to install the Weathertech No Drill Easy Install Mud Flaps for the rear, part number WT120088.Now, they're also available for the front using part number WT110088.So, here's what our mud flaps are gonna look like once we have them installed on our Expedition. These are gonna keep all that road debris from coming back and getting on the back bumper and protect our paint from any kind of rock, chips or scratches. And, if we're towing a trailer, it's gonna keep all that debris off the trailer, as well.Our mud flaps are gonna be digitally contoured, so they're gonna fit all the body lines perfectly. And the mud flaps are gonna be made out of a thermoplastic resin so they're gonna hold up for a long time.Our mud flaps are not gonna require any kind of drilling. They're gonna use all factory holes, as well as stainless steel hardware, so, we're not gonna have to worry about any rust or corrosion.So, now that we've seen what they look like, let's show you how to get 'em installed.To begin our installation, we're gonna come to the rear wheel, and along the edge of the wheel well here, we're gonna have four of these plastic fasteners. You'll want to use the included bit that comes in the kit, and you can use the socket or a bit driver to pull out the center, but I'm threading it, and when you're unthreading it, you want to be careful, you don't want to push too hard, because that center will go back in, but, you want to unthread that screw.
We can pull it out, and then we can pull out the rest of the push pin. And we'll repeat that for all four along the edge here.Once you remove the last one, we're gonna pull the wheel well liner back so we can expose all the holes that those fasteners we're in.So, if we grab our kit, we're gonna have these little U-nuts, and they're gonna be open at the bottom. We're gonna want to slide these over the plastic so they go over the factory holes. However, we're only going to be doing it on the top one, one down from that, and the very bottom one.So, you take your clip and you get it pretty close to lined up, and we're gonna want to slide it onto the plastic so the hole lines up with the factory hole. Now, the top one and the bottom one can be a little bit of a tight fit, just because we have our rear bumper in the way, but if you just pull away a little bit, we can get the clip in there and started, and we'll just squeeze it until it slides all the way on.And, the one on the top, you want to make sure you get it onto the black inner plastic and not on that white piece.With all those clips in place, we'll put our wheel wall liner back.So, we're on the right side, so, we'll grab the right-hand one.
We're gonna line up the holes, and we'll come up to that second one from the bottom, and we're gonna take the plastic push pin fastener that's included in the kit and we'll put it in, and that'll hold our mud flap in place while we get the rest of the hardware in.So, we'll take one of the included screws and a flat washer, and we're gonna get these started by hand in the remaining locations. And then we can come back with the bit that's included in the kit, and we can tighten them all up.With this mud flap done, we're gonna repeat the same process on the other side.That'll finish up your look at the Weathertech No Drill Easy Install Mud Flaps for the rear, part number WT120088.
Ratings & Reviews
Seems like a solid product. Made in the USA. The instructions were a bit off. So I jumped on the etrailer YouTube account, found the install video. Issue solved. I will say I'm more impressed with etrailer than weathertech. However, nice fit and finish. I would recommend this product.
Super easy install great factory look and they actually do help i have a white ram 2500 that used to look dirty from any water on the road 5 feet after the car wash now I dont have to wash my truck every day to keep it looking clean 5 car washes a week is $100 at $20 each so these pay for them selfs
Vehicle: 2026 Ram 3500 Dually. Ordering was simple with website identifying which items fits my truck. Arrived quickly and tracking update to date to prepare for arrival. Ordered for all 4 tires. Took less than 20 minutes using the 2 factory screws. Nice factory molded look. Awareness, The rear are shorter than your typical rubber mudflats.
I ordered Weather Tech mud flaps for my GMC Sierra 1500. The front flaps were easy to install by using existing fasteners installed on the truck by GMC. The rear flaps were slightly more challenging requiring the placement of clamps (integral to the flaps) on the rear fender. The entire installation of all flaps required about 45 minutes. they look great and they will protect my fenders from being damaged by road debris.
Are you serious with the question or is this just a computer generated inquiry?
This is a good investment. First, etrailer is a great place to get what you need for supplies! The weathertech mud flaps are a great addition to a raised F-250 with larger tires that pulls. This will provide the rest of the protection I need as well as cut down on debris that the tires throw up at other cars/trucks. Very easy to install and if I want to remove them then I have all the pieces necessary except for the push grommets which I can get anywhere. I think I will leave them on for a while....not bad looking either.
The Weather Tech mud flaps are very well made, fit perfectly and are very simple to install. I’m very impressed with them and they really help protect the body of my Jeep Grand Cherokee.
the fit was very good with the mud flaps fitting with my factory fender trim. The only issue was the clips that came with the setup. there were supposed to be 4 and there were only 2 in the packaging.
I purchased these for my wife's new 2031 chevy traverse. They look great and were easy to install. I have had many weather tech products through the years and have been very happy with them.
Fits my 2018 Chevy Silverado 1500 custom front steering wheels mud flaps. Bolts on correctly and fits good.
Weather tec is great, getting it from e trailer is also great. As the fit is always guaranteed. There customer service and follow up is second to none.
Mudflaps fit perfect and look great. Great business to deal with and fast shipping
Front mudflaps were easy to install. Rear mudflaps need a new design. Instead of a bolt, two washers, and a lock nut, WT should use some sort of insert into the whole where the bolt goes through. It is extremely difficult to get the washer and lock nut onto the bolt as the area is small. Something like a drywall anchor in the hole and then screw into the anchor. Finished product looks great. Please pass my comments onto Weather Tech.
Easy installation. Instructions are easy to understand.
Would have gave a 5 rating but had trouble with a flawed supplied screw clip so took a bit longer on the install. Had to remove the clip and modify so supplied screw would thread into clip. This happened to be the last screw to tighten.
WeatherTech products looks fantastic and are easy to install. This set was simple to install on a 2021 RAM Power Wagon
Quick shipping was always from etrailer. Product was a perfect fit on my vehicle and easy install took about 30 minutes.
These were easy to install and look great on my 2023 F350 dually. I was a little concerned about how close the passenger side one is to the exhaust tips. Have only used them on one 2 hour drive but so far so good.
These no drill mud flaps are easy to install and look factory after installation. I was told by Weather tech they would not fit my 2025 F450, but they were wrong, they fit perfectly. I wish they used black screws and washers, it would look more finished than an after thought with the stainless metal screws and washer. Great product, would recommend, thus the five star rating. I have been using Weather tech products for years.
Vehicle 2026 Ram 2500 Dually. Ordering was super easy to identify the mudflats for my vehicle. Quick delivery with tracking to prepare when they arrive. Installation: Use the 2 current factory screws on each fender for a quick install, less than 20 minutes for all 4 a nice clean factory molded look. Front length looks good. Just for awareness. The rear isn’t as long as your typical rubber mudflap if you are looking for something that hangs closer to the ground. Hopefully can see the length in the photos.
Great product. Excellent quality. Looks great. Very simple to install. Took about 15 minutes to install. Fit was perfect. No adjustments to make. Fast shipping.
Perfect fit. Easy install. Arrived in days of order...
This product is nicely done, and care was taken in shipping.
Not only do we often buy products from them, but their customer service is exceptional. Always get a response to every email. Impressive.
Our client will be very happy. These are nice.
Do you have a question about this Mud Flap?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.