To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Add heavy-duty tie-down anchors to your truck bed stake pockets with simple, no-drill installation. Retractable design allows stainless steel rings to snap up and down when needed.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we're taking a look at the Pro Grip retractable tie down anchors for truck bed stake pockets. The heavy duty anchor rings provide accessible tie down points for securing your load, or for securing your gear in your truck bed. This product has nice universal design to it. It is designed to fit most truck bed stake pockets, and it's retractable. When you're done using it you just push it down, it lays flat. When you're ready to use it you just pull it up, it snaps into place and it provides that nice tie down point.
The base is made from a durable plastic construction. The actual tie down ring is stainless steel. It has a ring diameter of 5/16 of an inch and it's an easy no drill installation. The anchor's simply fit into your truck bed stake pockets.What you'll need to do is you'll need to loosen it up to where it's positioned like this. You drop this portion into the stake pocket and then you lift up on the ring.
What that does is it brings this lower portion here, which is the clamp, brings it up kind of inside that bedrail area. Then you install the hardware, and then you just use a Phillips head screwdriver to tighten down the screws. There's no need to over tighten, you just want to get it hand tight. Once you have those tight, that's really all there is to it. It's a nice quick install.
It's very easy to use, very easy to install, very easy to operate. With this part number you get two tie down anchors.The anchor opening side to side measured 7/8 of an inch, bottom to top, that opening right there, is 1 inch. The base itself . I took a measurement from edge to edge going this direction and that measured about 3 3/8 inches to 3 1/2 inches, right in that ballpark. Edge to edge this direction is 2 1/4 inches.
When it's installed, the only portion that's going to be visible is this right there. It's a nice low profile design. Again, when you're ready to use it you grab the ring, pull it up until it snaps into place and you have your tie down point. These also have a weight capacity of 1,000 pounds. That's going to do it for today's look at the Pro Grip retractable tie down anchors for truck bed stake pockets.
Customer Satisfaction Score:
97% were satisfied with this product
3% of customers were not satisfied
Ratings & Reviews
Robert
7/16/2025
Works great! no problems so far
Lazer S.
7/16/2025
Gary
1/18/2021
Terrific
Gary
1/18/2021
Perfect fit, rugged performance, firewood does not scratch the paint
Theodore
7/20/2024
Still great, best ever would not use anything else
Brian
4/11/2022
Theyre still going strong. I wish Id had these years ago.
Stephen
4/22/2023
Perfect! Very reliable tie down point. I’ve hauled many loads since installing these and I couldn’t be happier!
William M.
8/6/2023
I have used these several times. Tied a tarp over the truck for winter storage. tied down a water jug and a gas can for travel. They stayed in place and have not come loose.
Do you have a question about this Truck Bed Tie Down?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Sierra K.
12/14/2021
The weight rating for these are 1000lbs combined. The rings are stainless steel. The plastic is meant to be corrosion resistant but is still connected via the metal plates for durability. These fit with or without bed rail caps and should not be loose. Your 2004 Dodge Ram Pickup is listed to fit and the hole is the same size whether or not there are bed rail caps. I would tighten the anchor point very tightly.