Summer Starts Here - Save up to 70%
# 1
Stromberg Carlson Electric A-Frame Tongue Jack - 18" Lift - 2,500 lbs
This is the second one of these we've owned. Works real good, a bit of over kill. The thing could probably lift the whole trailer.
It installed very easy. For a 2500lbs jack, it seems a little light weight. It does lift the trailer but seems kinda wobbly because the post size is so small. Other than that it works as advertised. Thank you for getting it to me so fast.
# 2
Lippert Power Stance Electric Trailer Jack w/ 7-Way Plug - A-Frame - 18" Lift - 3,500 lbs
The alternate power setup makes its slow rate of rise necessary which would be good if my lithium batteries went low. To avoid battery problems be sure to add an inline battery disconnect from the trailer power when using tow vehicle power. I simple added an inline fuse that could be removed should I need to use the tow vehicle power.
I was amazed at how quickly my replacement from etrailer arrived. I was a bit worried that the installation of my new jack would be more difficult that I expected. The reverse proved to be the case, it was very simple to place the trailer tongue on jack stands, remove the old jack and install the new one. As the old saying goes "even a cave man could do it."
# 3
Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System - 10,000 lbs
One small part was missing from my Ground Control TT. Carol Korren expedited delivery of the missing part and the UPS truck pulled up at the moment I needed the part. Fantastic customer service!
We love our one touch jack system. We used in on a 3 month camping trip out west setting up probably 40 plus times and we continue to use our camper and the jacks work great!
# 4
Lippert High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift
Easy to install and functioned perfectly. Customer has been utilizing it for a year and still raves about it. Thank you
Pros: Works better than I anticipated. Looks great and has better ground clearance than the stock scissor-jack stabilizers. Cons: Installation instructions/documentation weak or non-existent. If all of the instructions, wiring diagrams and documentation were in one place on the web page under a separate tab rather than having to dig through the reviews and the Q & A’s, I would have given this a 5 star rating. I ordered the LCI Power Stabilizer Jacks with the white switch Kit (LC369774) because I wanted the switches mounted in the camper wall so they would be better protected than if they were mounted in the flimsy fender skirts of my camper. I also needed the bolt-on spacer kit (LC673594) for both the front and rear jacks to clear a propane line that runs along the length of the frame. Installation was relatively easy, although there are NO instructions on how to install the spacers kits; the video on etrailer.com was no help whatsoever with the installation. I bolted the jack mount brackets to the shorter side of the spacers using carriage bolts and flange nuts; the slotted holes in the spacers accepted the carriage bolts, aligned perfectly with the holes in the jack mounts, and allowed me to install them without having to try to fit a wrench inside. Then it was just a matter of drilling holes in the frame at the appropriate spacing for flange bolts/nuts through the slotted holes on the end of spacers. I was very pleased with how the switches and the switch compartments looked once installed. Again, though, it took lots of digging to find the wiring diagram and then the matrix for the switch wire colors, because the wires on the white switch are colored differently than the black switch that all of the diagrams show. Also, it states on the jack installation instruction sheet that the power must be a minimum of 10 gauge wire (AWG-10), but nowhere on the wiring diagram does it say anything about that. AWG-10 is a MUST because of the way current drops over a distance. In the case of my camper, it is a 30 foot run which requires that gauge of wire for 20 AMPs.
# 5
Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors - 30" Lift - 6,000 lbs
Finally got around to installing my PT II Stabilizers 30" front and rear of our 26' Surveyor. Pre - assembled them to make sure they went together ok. Luckily I had two sources for power front & rear which made wiring easy, I used a Buss block to make all positive connections, grounds straight to frame, soldered all connections and heat srinked to seal. Using the 3/8" self tappers was fun.Well got it all together and all works well makes trailer very stable, don't have to worry about scissor jacks collapsing anymore.
It looks like a great product am anxious to install them. I have a symbol of them in my garage and I have one with a really crooked foot. The bolt hole on the retracting arm was drilled in the wrong place so it is totally crooked, not a deal breaker though. I’m sure the are more than Adequate
# 6
Phoenix Electric Trailer Jack with Remote - A-Frame - 26" Lift - 5,500 lbs
This is awesome and so easy to install. Took longer to open the box then to set it up. We had ordered something similar to this for our old camper. It took us hours to get it to fit right. This was extremely easy to install. My husband loves the memory feature on this thing.
Best addition to my trailer, wish I got it sooner!
What our customers are saying:
"GREAT JOB! Lightening fast response and shipping."