Most Popular 500 lbs Vert Load for 2020 GMC Sierra 2500

Hitch fit perfect on my truck and the video was on point for installation. I had the hitch installed in 45 minutes and it looks great.

This was easy to install. I would recommend a second set of hands. 30 minutes and was done. Its working out very well. I can now carry my kayaks when we pull our fifth wheel.

Fit perfect on my 2017 GMC Denali 2500HD Duramax! Very minor trimming of the sheet metal behind the license plate. I cut the front plastic first, based on the directions using a dremel tool. Once i did that, it gave me access to the sheet metal behind to cut out. One that was done, the receiver fit in place and bolted down with out a hitch! No pun intended :)

Click to Enlarge

Click to Enlarge

Very well built hitch. Was disappointed I needed to do some touch up paint before installing but very happy with the hitch. Instillation went pretty smoothly and looks great.

Great fit as advertised a little more work than the video but my truck is a Denali so some extra work to expose the bolts.All good though!

Install went perfectly. It all bolted up just how the instructions said it would. The hardest part was navigating your tools in the tight spaces. Having the deep sockets as suggested is definitely worth it. I was also able to utilize a cordless impact wrench and it helped a ton. This will work great for our bike rack.

Click to Enlarge

Click to Enlarge

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Click to Enlarge

Click to Enlarge

I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Great customer service and product.

The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.

This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.

These is an excellent hitch at an excellent price. The install was easy and all the hardware that is needed is in the box. I chose the Drawtite over the Curt because the receiver end is a little longer. It' not even noticeable on the truck. I have a snow plow that attaches to the hitch. The Toyota cap shown in the picture was not included. The Tundra is a 2020 so I can confirm if fits.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.

Click to Enlarge

Click to Enlarge

I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.

Click to Enlarge

Very easy to install. works great for bike rack and generator box.

After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

Click to Enlarge

Click to Enlarge

Click to Enlarge

Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.

How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

This hitch was very easy to install....I had to trim the lower air dam to fit around the receiver and that gives it a clean neat look. I didn't like that I had to remove and leave the shields around the tow hooks off. But overall I'm very pleased. I plan to use this hitch for maneuvering a camper in a narrow spot beside my home, and for a bike rack when towing a camper.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installing onto my 2014 Silverado 1500 was a breeze. The only thing that caught me off guard was that I needed to cut a portion from the center of my splash guard for the rear bracket to be able to mount. I was only expecting to trim/remove the air dam as etrailer explained in the item description, which I still had to do. Other than that it was a perfect fit and I'm happy with the results. I plan to use this for a snow plow, winch, and many more interchangeable items for it.

Click to Enlarge

I installed this front hitch by myself on a 2016 Chevy Suburban in about 3.5 hours with no floor jack. I use it to carry my mountain bikes when we are towing the trailer. The hitch sits 8.25” off the ground and extends out past the air dam about 3.5”. Once installed, the hitch is not very noticeable. A couple notes on the install: 1. The most difficult part is figuring out where to make the hole in the splash shield for the rear mounting point. I removed the splash shield and determined roughly where to cut a 1.5” hole based on the existing holes in the cross member. 2. To cut the air dam, I drilled small holes the the corners then used a utility knife to score and cut out the section. 3. I mounted the rear point first which gave me leverage to install the front easier. 4. The tape method for the 9/16 hardened washer and cone washer did not work for me. I had to finagle them into position as I was tightening the bolts (huge pain) 5. I had 4 extra 9/16 hardened washers. These are apparently supplied in case you need additional washers to fill the gap in the frame. I am very satisfied with this product and would definitely recommend it to others.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Easy to install. Works perfect to hook up car trailer to front of rv when camped for days at the track.

Click to Enlarge

It's holding up a Thule rack well. The rear is freed for a motorcycle.

Click to Enlarge

Click to Enlarge

Click to Enlarge

I got the hitch and made a appointment to have it put on. That fell through so I decided to tackle it myself. It was extremely easy, my wife helped hold it in place while I got the bolts started. I use the hitch which I install in the front of my 2500 Ram to haul my ebikes on a bike rack. Works excellent.

Click to Enlarge

This hitch is fantastic, it was easy to install and with it I am now able to maneuver my 26 foot boat through the narrow opening of my fence and onto a concrete slab. The ordering process was fast and easy and the shipping to Hawaii was reasonable and got the hitch in just a few days. I also really appreciate the follow up asking if the item and install went ok. I will definitely order from etrailer for all my future trailering needs.

For a business that is based on shipping everything they need to learn how to package stuff. Everything I received from a trailer comes damaged at this point.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Installed on my 2019 GMC Sierra 1500 Denali. Shipping box was destroyed & poorly packed. Instructions were straightforward. Install took 1 1/2 hrs. I only trimmed the thin trim without cutting the skid plate. The receiver pushes up on the skid plate slightly, but I didn’t want to cut it. Should work great for my E-bikes when pulling the RV.

It was a bit harder to put on than they show in the video. Did it by myself, everything fit perfect SO OWSOME! I would recommend anybody. Truck or car should add one. Very convenient and can be use for many different purposes.the rack on the back, I now put in the front with generator gas tools and it works as steps. So now I can tow trailer, or jet ski. Having that front hitch is so cool. You could even attach a car whinch in the receiver.

Click to Enlarge

Click to Enlarge

Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.

Click to Enlarge

Product is great! Exceeds my expectations for ease of installation and performance. I removed the 3” spoiler completely vs cutting for hitch. The key is to “dry fit” in place and use a metal punch to mark all your drill holes. Wire bolt feeder worked great for installing bolts. I used the hitch to mount my eight pole rod & cooler holder for surf fishing.

Click to Enlarge

Super fast shipping,but could use better packing.Hitch actually made a large hole in box,UPS driver had me check to see if anything was missing.Easy install,but try finding a 17/32" bit. After seeing how big the front opening is I just used a 1/2" bit. I think it took longer to remove, trim and reinstall the front spoiler than the rest of the job. Looks great installed

Click to Enlarge

Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Primarily bought the front receiver hitch to haul our 2 e-bikes. Did that because it was easier than hauling them inside our camper. And didn’t trust them bouncing around on the back bumper of the camper. Hauled the bikes that way on several camping trips. Easy as pie and I could keep an eye on them the whole trip.

This worked great on my F350 dually. We needed a front hitch to carry bikes while towing a 5th wheel camper. Instructions were easy to follow

Click to Enlarge

I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.

Click to Enlarge

This receiver performs well for both bicycle and motorcycle carriers. It is not obtrusive when not being used. It was easy to install with no drilling required (You do have to cut out the air dam.). I would have given 5 stars if would’ve fit a little higher. There was room for it to be at least an inch further off the ground. I ended up putting a 1 inch leveling kit on the front of my 2 wheel drive F150 and it turned out great and the truck looks better too

I am very pleased with this equipment. Bought it to carry two heavy E-bikes. Installation directions could have been clearer--but with the help of videos, I got it in just fine. Had to use a large crow bar to urge it in place though.

Click to Enlarge

Click to Enlarge

The receiver was very easy to install and fit like a glove. I have installed a 12000 # winch for when I go hunting. Thank You , Gwendolyn for your help you were great to work with.

Click to Enlarge

Click to Enlarge

Great product. Installed in 45 minutes. Very easy. Love it

Click to Enlarge