Most Popular Long Shank for 2018 Volvo XC90

Fits our VW Touareg perfectly and allows us to tow a variety of things now. As can be seen in the pictures the hitch has a +5-inch gap between the bumper and the vertical adjustment pillar and the trailer itself is out further so there's enough room to get to the rear hatch and maneuver the vehicle/trailer.

I needed a hitch that I could haul my work trailer with and still drop the tailgate without dropping the trailer. I looked on etrailer and found one that would work barely but decided to call etrailer and see if anyone had any ideas. Steve answered and looked after I told him my requirements and came up with this. This has a longer distance from ball to pin by a few inches compared to the one I found so my tailgate will still drop even if I’m at an angle to my trailer or on a hill. Also with the adjustable height it’s great. Awesome hitch. Solid for a good price. ??

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

Looks to be a well built hitch there's virtually no other 12" drop hitches short of expensive adjustable ones it's just about right for my custom bumper

Arrived today. Fast shipping, and thank you for that! Seems to be a quality ball mount. Just what I needed to get the ball lower to tow my trailer. With this, now the top of the ball is at 16" where it needs to be. Custom built receiver on my old moving box van. Just need to weld on safety chain slots and paint it. Can't drop the lift gate with the receiver in (its pinned on both sides), but hey....I can tow now.

Very nice ball mount. Smooth, one piece design. Unlike my previous ball mount, it's long enough (enough straight length between the pin hole and the beginning of the bend) to accommodate a Blue Ox Hitch Receiver Immobilizer II, yielding a nice, tight connection. Attractive polished finish. Made in Taiwan (according to the box it came in). Photos show it attached to a Hidden Hitch Class III Hitch Receiver, secured with a Blue Ox Hitch Receiver Immobilizer II, and a Curt 40053 2-inch stainless steel ball.

Great looking product and fast service as usual. Now I can keep it clean and stored under my seat without the grease and rust issue. The ball mount with the 2" Brophy stainless ball and the Master Lock Pivot Hitch pin work perfect. Thanks, Garland R in Kentucky...…….

I needed an extended ball mount for my new Jeep in order for my utility trailer tongue to clear the rear mounted spare tire. Item is as described on the web site and was received earlier than expected. etrailer has great customer service and is my number one go to place for towing and trailer supplies.

Overall, I have to say that I am satisfied although not particularily impressed. The finish on the ball mount is mediocre ... there are several spots where the paint is chipped off for instance. It was received today and installed today with no use yet the pictures show the areas in question. You can tell by the label installation that someone who really didn't care rushed the operation. It also fit considerably looser than the Reese bar that I removed. I had to apply several turns of duct tape around the tube to make it as snug as the original. As I said, it'll do fine, just not impressed.

Just what I needed, most receivers would not allow me to open the tail gate on my 2022 dodge ram without hitting the trailers crank used to mount and dismount the car hauler trailer, this receiver give me the extra few inches I needed and it works perfectly, I tried many local sources but they all came up too short, etrailer is the place to go for all trailer parts, they seem to know and sell exactly what you may need

For a 7,500 lb hitch, I was surprised it didn’t have a wedge support welded on where the flat iron is welded to the square tube.

Heavy duty , very good quality.

Great ball mount for my wife’s SUV allows her to pull the golf cart with the trailer level

Let the packing/shipping department know they should've used a bigger box and packed it differently? Kinda disappointed as this isn't the first time stuff has been battle-scarred before I get it. Considering my next steps.