Most Popular Flush Pin for 2018 Subaru Crosstrek

Fast shipping & great quality. Would buy again!

High quality! Should last for many years!

I have not yet had a chance to use this lock as I just got it after getting home from a long road trip. However, I have other MasterLock locks for my flat tow set up. I really like these which is why I got this one to replace an older lock that had some rust issues. I'll follow-up once I get some extended use.

It's easy to lock and unlock, but since I'm only using it with 1 vehicle, I'll probably just leave it attached. Even with the dust cover, I figured it was a good idea to squirt lubricant into the keyhole. Along with the ball-hitch lock I got from etrailer (also excellent) it provides peace of mind.

This is probably one of the best stainless hitch locks of the regular through-pin style locks. It installs flush, and uses a solid pin. The locking side is also beefier than most, and sits tighter and deeper on the pin than most other pin locks - making it harder to try and hammer it off, or getting at the pin with a cutting tool. The lock uses large solid ball bearings for the lockup, and a disk style locking mechanism, which is harder to pick without specialty tools. So overall, one of the best regular pin style locks. We towed a 6'x12' that weighed around 6,000lbs from PA to FL without any issues with the pin-lock. We actually had to disconnect our trailer along the way, a few times, and the pin was easy to work with, and the lock really smooth. Don't hesitate to get it.

I purchased this Bulldog pin for my 2015 Yukon with a factory installed hitch. In this application this Bulldog hitch pin fits very well. I selected this pin due to its simple design and the generally compact diameter of the lock cylinder and the pin's beveled head-end. The lock cylinder diameter is import since GM penetrates the nominal 2" ID hitch tube through a steel bulkhead. There is only 7/16" distance between the hitch tube's nominal 5/8" clearance hole edge and the face of the factory bulkhead. Also, the hitch tube is fillet welded to the bulkhead. Thus, both the pin head and the lock cylinder need to have some relief (i.e. the bevel on the pin head-end) in order to clear this external bulkhead weld. Most of the above fitment concerns are overcome by the Bulldog pin's grip length being greater than that listed on the etrailer site (and in their videos as well). Specifically, the grip length is 2-11/16" rather than the listed 2-1/2". See the attached photos. Note that in the first photo the lock cylinder is firmly seated on the ball locking end of the pin. In the photo note that the cylinder is fully engaged and locked, which would not be possible if the cylinder was not fully seated on the pin end. The first photo shows the dial caliper fully closed and properly reading zero. Also note that the GM hitch tube is 2-9/16" square (outside dim.), thus technically a 2-1/2" pin grip length would be inadequate in this application. Since I have a metal turning lathe I was prepared to machine the pin a slight amount in order to make it fit. Thankfully, this was not necessary since the grip length is 3/16" greater than advertised. The pin is Chinese made in "stainless steel". I did test the pin with a magnet and it does appear to be austinitic (high enough in Ni and Cr alloys) since the magnet had no attaction to the pin. I do like that the lock cyklinder has an internal o-ring to help keep out "road splatter". I also gave the lock cylinder a short squit of WD-40. In sum, a well designed rugged product at a fair price.

Fit is perfect for a 2.5” receiver.

I hate this lock. Why? Because it requires three hands to operate it, and so it's incredibly difficult to install it by yourself. You need one hand for the key, another hand to hold the lock end, and a third hand to push the non-locking end tight against the receiver. I had a locking pin then went with a trailer I sold, and I wish I knew which brand it was, so I could get another.

Fast delivery.. They look heavy duty!

Works as expected. Fits my Pro Series Adjustable ball mount perfectly.

Last year I bought a flat tow set up for my jeep and Rv E trailer delivered me a great set up Hitch. Hitch locks. Cables. Demco braking system. Base plate and plugs. Easy to install and great towing

The locks worked well for Fastway trailer hitch.

As I have always said etrailer is the only go to for all my trailer parts…….everything I have ordered came on time and was exactly what I ordered

I drive a 2015 Ford F250. Using the OEM reduction sleeve to drop down to a 2 inch shank was causing problems. I was bending class five hitch pins. After bending my third pin I was anxious to find another solution. This product has been terrific. All the play has been taken out... leaving a very solid trailer to truck connection and no more bent pins.

etrailers blue ox Hitch receiver Lock works great I’m confident no one can mess with it while I am at dinner or at my campsite or just going into a gas station etrailer has what you need very good business

A must have your hitch receiver safe from being stolen

Perfect fit for the receiver on my '97 F350