Summer Starts Here - Save up to 70%
# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Works as advertised
The trailer hitch ball mount fits great. The floor mats for on the 2016 Honda Odyssey fits nicely and the color choice turn out nice.
# 2
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 3
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
I wanted to attach a small luggage carrier behind my odyssey. I had to grill another mounting hole to alter the angle so it would not drag. Excellent product. Was able to customize it easily. Thank you.
Works as intended, pretty rock solid. Note on here said to only use it in the RISE position, not the drop position.
# 4
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
I ordered this extra length ball mount to keep the back end of my Honda Odyssey out of the water when I launched my boat. It does exactly what I wanted. It connects with the hitch I purchased from etrailer last year. Going to etrailer was my first step when I realized I needed additional length. I wish that more Internet companies had the service I get from etrailer. John Boddie
Great!
# 5
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
This was part of the entire "Hitch System" I ordered for eTrailer. Everything fit together without any problems. Feel to this particular part is heavy and well over-designed to ensure performance and safety. Very confident that it will last long after the vehicle it is connected to is gone.
This long-shaft ball mount enabled me to fully insert and pin the shaft and get the rise I needed for towing level a Yakima Trailer by a 2015 Honda Odyssey. The typical, shorter shaft was not long enough for complete insertion and pinning of the shaft because the welded on arm-support piece hit the bumper.
# 6
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
What our customers are saying:
"Fast shiping and great communication. Product was very easy to install and it came with great directions. Very happy with this company."