# 1
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
My son and I finished putting on both hitches front and rear, Rear was very easy after we cleaned out the rust. The front was a little bit of a chore because we did it with car ramps and it took some maneuvering to get the bolts tightened down. But we got it done and it looks great on my Liberty. Pictures above. I would definitely recommend you guys, the instructions were very helpful. Will do a review tomorrow gotta watch the games now.
Very well made and really fast delivery, excellent transaction and the people at trailer put a lot of effort into seeing you get your order
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Since I had the ARB Winch Bumper already installed this product had to be heavily modified to fit to include cutting and welding. NOTE: Instructions contain Contradictory Torque specs for the 7/16 hardware. On One page Step #9 says torque to 70 lbs, while a different page Step #9 says 59 lbs. 70 lbs, will ring off the bolt....
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Have used it a few times last fall to carry a cooler and fishing rod cart on the beach. So far have not had to use as a recovery to get pulled out of sand or pull another vehicle with the tow strap loop attachment that I bought as an additional accessory. The top mount on the bumper was ideal since gives more clearance than below bumper mount when in the sand. Keeps the cart up high. The paint on the hitch is very nice.
The item was packaged poorly causing me to have to touch up prior to installation. Large box with no stuffing causing the item to rattle around. Probably got scratched on staples in the center of the box that served no purpose. The installation instruction were unclear and contained errors. There we multiple washers and you had to guess as to where to use them. Instructions showed bolts installed where there on holes
# 4
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitch came packaged in a double box. The outer box had some damage but the hitch did not. I read the instructions, making sure i had the correct tools, and jacked my truck up. The install took three hours as i was layiing on my back with simple hand tools. The parts all fit and i am happy with the outcome. Good price, simple instructions, good fit.
I bought the Curt front hitch for the purpose to haul my Honda Generator on the Torklift Lock and Load in front of my 2009 Chevy Silverado. The installation is self explanatory, but I still watched the video provided by e-trailer, and it made it that much easier to put in. Especially by myself. It works perfectly for the purpose I bought it for.
# 6
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!
I bought and installed the front hitch to my 2014 Toyota Tundra because I did not want to use my travel trailer's rear bumper. The 2014 Toyota Tundra has a skid plate that has to be removed for oil changes and this front hitch installed would also have to be removed each time the oil is changed. I decided to cut a square hole in the skid plate allowing access to the oil filter so that the skid plate along with the front hitch would not have to be removed to get to the oil filter. The skid plate has 5 bolts and 3 screws and drops down for oil changes. To completely remove the skid plate after removing the bolts and screws you have to hold the skid plate and move it to the drivers side to unhook two hooks which are "L" shape facing the same way towards the passengers side. Do not leave the skid plate off because too many hoses and lines will be exposed and can be damaged while driving. It took me less than 20 minutes to install the front hitch and I also bought a Hitch Extender for a 2" Trailer Hitch 7" which made the hitch come even with the front bumper on my 2014 Toyota Tundra. I bought several other accessories to go with the front hitch which I can use when needed. I did buy this hitch mainly to use to carry my 2 beach cruiser bikes and it works perfect. Now all I have to do is insert the bike carrier into the receiver hitch and load the bikes and I am off with no worries about the bikes being in the rear of my travel trailer or trying to keep them steady in the bed of my Tundra. The bikes look really good in front of my Tundra and my driving view is not blocked at all with the bikes on. With the 7 inch extender the bikes are nowhere near the truck and with the Anti-rattle with lock on the 7" trailer hitch receiver there is no swaying while on the road or on the freeway at any speed. Thanks etrailer.
# 7
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.
# 8
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Well built, solid receiver hitch. I had to make minor modifications to get it to fit the gladiator mojave because of the fox shock mounts
Jeep WranglerFits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 10
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 12
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.
This hitch was very easy to install....I had to trim the lower air dam to fit around the receiver and that gives it a clean neat look. I didn't like that I had to remove and leave the shields around the tow hooks off. But overall I'm very pleased. I plan to use this hitch for maneuvering a camper in a narrow spot beside my home, and for a bike rack when towing a camper.
# 13
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great customer service and product.
The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2007 Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
These is an excellent hitch at an excellent price. The install was easy and all the hardware that is needed is in the box. I chose the Drawtite over the Curt because the receiver end is a little longer. It' not even noticeable on the truck. I have a snow plow that attaches to the hitch. The Toyota cap shown in the picture was not included. The Tundra is a 2020 so I can confirm if fits.
# 15
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Install went perfectly. It all bolted up just how the instructions said it would. The hardest part was navigating your tools in the tight spaces. Having the deep sockets as suggested is definitely worth it. I was also able to utilize a cordless impact wrench and it helped a ton. This will work great for our bike rack.
Delivery was super fast, instructions and instructional video was excellent. Installed my new part in less than 40 minutes
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Product is great! Exceeds my expectations for ease of installation and performance. I removed the 3” spoiler completely vs cutting for hitch. The key is to “dry fit” in place and use a metal punch to mark all your drill holes. Wire bolt feeder worked great for installing bolts. I used the hitch to mount my eight pole rod & cooler holder for surf fishing.
Super fast shipping,but could use better packing.Hitch actually made a large hole in box,UPS driver had me check to see if anything was missing.Easy install,but try finding a 17/32" bit. After seeing how big the front opening is I just used a 1/2" bit. I think it took longer to remove, trim and reinstall the front spoiler than the rest of the job. Looks great installed
# 18
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
use front hitch to hold a DR snowplow, I have a very large driveway and had looked for a economical way to push snow and both pieces of equipment are doing a excellent job. no problems, easy to install hitch and heavyduty enough for my application. would recommend to anyone .
Hitch looks to be very high quality. Only problem am short 1 7/16 nut. Will install soon.
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Quality hitch and the excellent service all the way around I'm used to getting from etrailer over the years. Installed on my 2016 Sierra Denali 2500HD, note instructions say on first line down that it does not fit the Denali trim due to extensive fascia cutting required; actually it was quite simple with the aid of a 4-1/2" cutoff disk and a sawzall. Installation is much easier with two people. See attached pics for actual material removed, note the lower fascia need not be cut for the hitch to fit through the hole. Maybe more work to install than the Curt hitch, but well worth the additional ground clearance.
The hitch was easy to install. The only issue is who ever welded it put the front ring on and it's turned to one side. It functions fine but bothers my OCD.
# 20
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Picked this up from etrailer for a great price, so i can put a hitch-mounted winch on the front of our race tow vehicle (and perhaps use it to get the trailer into tight spots). As always with etrailer, it was delivered quick (and free!). One of the arms was just slightly bent (perhaps from shipment) so I had to whack it a couple times with a heavy hammer to get the holes to line up, but after that it fit perfectly. The little "fishing" tool included is extremely handy for installing the two bolts that need to come from inside the frame of the truck. All in all, quality is great and this particular one fits with my factory skidplate/splashguard with a small amount of trimming with some metal shears. PS - we also have stuff from etrailer on the rear end. Highly recommend anything you buy from etrailer!
My hitch arrived quickly and my mechanic installed it in 1.5 hours for me a few days later. The factory skid plate fits nicely with 2 holes cut as a modification. His only concern is he will now have to use hand tools instead of his air tools on some bolts holding the skid plate at oil change time. But no big deal at all. I keep a 16 foot boat in my warehouse and maneuvering room is very tight. The door is narrow and there is a building across from my door that leaves very little room to maneuver my truck in. With my new front hitch I put the boat in the warehouse in less than a minute the first try. The front hitch makes it easier in 2 ways: 1) visibility-you can see what you are doing. You are closer to your work and you are looking straight at it. 2) with the trailer closer to the front wheels you can do things in tight quarters that just can't happen working with the rear hitch. Using the rear hitch the front of your truck would hit the wall of the opposite building. My only regret is not getting this ten years ago. I recommend a front hitch to anyone who needs to maneuver a trailer in tight spaces.
What our customers are saying:
"Your internet site is very well organized and easy to use...My order was shipped very promptly and included everything I ordered...All in all this was a simple procedure for what can be a complicated order. I would use your company again or recommend you to others. Your selection was broad and your prices fair."