# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
I searched the internet to put a hitch on my 2016 Chevy Equinox and found an instructional video from eTrailer.com where they installed on my exact car. I decided to go with eTrailer.com because they answered all my questions and because of the video-I support businesses that go the extra mile with these videos. Shipping was quick and well tracked, however, the box was flimsy and the one end of the hitch had come out of the box side and the ball mount could have easily come out of that hole during shipping. If I were eTrailer.com I'd charge an extra couple of bucks for more sturdy boxes-people will still buy as eTrailer is a well-trusted brand and this would overcome a lot of the negative reviews you'll see on their site about this shipping issue in their own reviews :-) I installed the hitch by myself (definitely recommend help as two people holding it up to the frame makes attaching 100% easier) in about 45 minutes total (out of the box, read instructions, review video again and installation complete). All hardware went on with no issues. Great quality hitch! I also bought the lesser expensive wiring assembly because most recent equinox's come hitch ready with pre-wired assembly in the left side compartment-snap and done. Picked up a new trailer at Home Depot within days and drove 5 feet and the clacking was horrible. I had always had a welded hitch before buying a hitch that took a ball mount. I really thought something was wrong and when I searched the internet that night it turns out this is very common. However, all you need is some sort of hitch "silencing" device. The number of options will drive you mad but I went with the Roadmaster Quiet Hitch and it did the trick for much less than most of the other options. If I were eTrailer.com I'd have that as one of the RECOMMENDED add-ons and explanation why its super-worthy when customers are buying a hitch. Would have saved me the time and hassle of dealing with it later and the extra shipping charge for buying after the fact when I got free shipping for the other items the first time :-) All in all, I'm super, super happy with my hitch, wiring assembly, ball mount, ball mount locking pin and the hitch silencer. Buy with confidence from eTrailer.com Paul R., Syracuse, NY
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.
# 3
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
Easy to use and haven't had any trouble towing my small trailer with motorcycle on board. Def recommend.
This part came with the trailer hitch I purchased. It was very easy to transfer the ball from my 2" hitch and voila I am now ready to haul my trailer.
# 4
Draw-Tite Ball Mount for 2" Hitch - 1" Rise, 2" Drop - 8-1/2" Long - 12,000 lbs
Quality seems good even though it’s made in China. Welds are perfect. I love these Zinc plated drawbars with the solid shank. In New England the cheap painted steel ones with tube shank rust out from the inside. Hopefully the plating holds up as long as the older US made ones we have.
As always with etrailer, the product I ordered (12,000 lb ball mount) is exactly what I ordered and arrived sooner than the original promised date. These folks are awesome to deal with and prices are always competetive. Thanks to the staff at etrailer!
What our customers are saying:
"Thanks for the great service. The order arrived at my doorstep yesterday afternoon. Thank you for making sure the order was complete. I installed the hitch and wire kit last night with no problems. The instructions were perfect. Bruce"