Summer Starts Here - Save up to 70%
# 1
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
It's a receiver hitch! It's well built, the welds are clean and it fits the trailer hitch. Not much else to say!
Good quality and fit. Installation was straight forward and instructions were accurate.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Quick delivery. Good service. Thank you!
Finished nicely and fit perfectly, except had to take a file to the inside of the receiver as the punched holes deformed the tube slightly. Now...smooth!
# 3
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
solid piece of construction. fits well in 2" receiver
Excellent item delivered in a reasonable time. The items exceeded my minimum needs in many ways.
# 4
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
# 5
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
The Curt Class II Drawbar with a 5" rise very nicely solved my problem when hooking up my two trailers to my Rave 4. The trailer jack was as low as it could go when it rested on the ball in my of setup. Now I have plenty of jack room to hook up and unhook. Thanks for your excellent product and service. Ralph E.
# 6
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 7
Curt Class II Euro Style Drawbar with 2" Ball - 2-3/4" Rise - 3,500 lbs
Overall I was a little concerned because I had read that shipping was fast but my hitch arrived slower than expected which caused a delay in my plans by weeks. Than when the hitch arrived it had no hinge pin. A little disappointed. I do not take pleasure in writing poor reviews
Nice item however I had to return due to it would be hitting my spare tire on my RAV4. I was not able to install it. On other vehicles with no spare tire on the rear door I think it would be awesome
# 8
Reese Trailer Hitch Starter Ball Mount Kit
I have not used it yet but looks to be good quality and I'm sure it will be fine
# 9
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
Ordered this product for my 2015 Rav 4 and it has worked perfectly. I tow a trailer about 4 times a week and needed a hitch that would step the ball up to make the trailer level and allow the wheel to be lowered without manually lifting the trailer myself. Product came quickly and was advertised. Would order again if I needed one for another vehicle.
# 10
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Quick delivery. Good service. Thank you!
Excellent hitch receiver. Perfect fit, nice welds, easy install.
# 11
Curt Class II Drawbar - 3-7/8" Rise - 13-1/2" Long - 3,500 lbs
The 5 inch rise on this hitch ball mount was perfect for my 07 Toyota Rav4. The rear door opens to the side on this year Rav4 and it has plenty of clearance. I tow a 16 ft aluminium boat and this 5 inch rise ball mount works perfectly on the Rav.
Ordered this product for my 2015 Rav 4 and it has worked perfectly. I tow a trailer about 4 times a week and needed a hitch that would step the ball up to make the trailer level and allow the wheel to be lowered without manually lifting the trailer myself. Product came quickly and was advertised. Would order again if I needed one for another vehicle.
# 12
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Quick delivery. Good service. Thank you!
Hitch installation went well after viewing the installation video. The wiring harness video was not completely accurate but provided more than enough visual information to perform the wiring install in a reasonable time. Overall, very happy with product at this time due to easy install due to seller videos. Haven;'t used it yet other than to take a test drive, so, sorry no videos, Etrailer provides a good product with excellent product support. Shipping was very fast and of course the price was right. I would definitely use them again.
What our customers are saying:
"Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast."