# 1
Hopkins Active Tail Light Converter with Install Kit
Installed on a 2009 328i BMW, took more work to get interior panels off/on in trunk area than the wiring. I had the electrical wiring diagrams for the car which really helped.
# 2
35 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 42" Ground
Replaced the wiring and lights on my 1992 boat trailer. I was able to get everything needed from etrailer. I think Optronics is of the highest quality and recommend both etrailer and Optronics product.
Works very well after re-wiring trailer lights with waterproof distribution box.
# 3
Modulite Protector 5-Way Flat w/ Integrated Circuit and Overload Protection
One year review - I installed this on a 2017 Armada. The install while straight forward did require removing some interior panels to access wiring. I have about 15,000 miles of towing a travel trailer on this device and it has worked perfectly.
After another store botched my SUV wiring installation leading to a short circuit and a need to rewire, I found this item for a great price. I wired it myself. It was simple and has worked perfectly with my LED lights and new trailer wiring. Very happy.
# 4
20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
Just what I needed for my home-built bike carrier. My wife rides an e-tricycle and by the time I loaded the trike and a couple of bikes on this platform, you could not see the car's taillights or blinkers. This harness worked perfectly!
Harness is made well. Installation was vey easy.
# 5
7-Way Molded Trailer Wire Connector, 6' Long
Only gave 4 stars because it was a bit confusing. I have a lot of auto wiring experience; from car stereos,amplifiers and all manner of accessories. All of the info on etrailer indicated that the color coding didn't match up. So I went into it disregarding the standard color coding, when in fact it was just as it should be.
Good thick rubber and plug works perfectly.
# 6
Great product no issues at all. Product as described & fit properly.
Pretty straight forward. I used it to switch my European trailer's connection to be able to connect to my Wrangler's 4-pin trailer hookup. No issues. works great.
# 7
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
Çable good but after putting new 7way plug on truck cable wire colors did not match etrailers picture
7 pin connector separated from cable. I was expecting that "Molded Cable" meant that the connector was fused to the cable insulation but instead, the two separated almost immediately after I installed it. It still works fine as the wires are connected securely inside the connector but with the outer covering pulled out like this, I don't think it will last very long.
# 8
Hopkins Endurance Multi-Tow 7-, 5- and 4-Way Flat Trailer Connector - Vehicle End - Ergonomic Design
Installed the Hopkins muti-tow 7, 5, and 4 way flat connector this morning. I ripped the original connector that was attached to the bottom of the hitch receiver off when I was 4-wheeling into the Doll House campgrounds in the Maze District of Canyonlands a month ago. So, I cut a hole in the bumper and mounted the new Hopkins connector, cut off the old broken connector mounting bracket, and connected the factory wiring to the new Hopkins device. Hopkins product installed easily, looks great, is now out of the way, and has the flexibility of multiple trailer connectors when required. I am pleased with the product. Attached is a photo.
Exactly what we had been looking for. Now I can hook up multiple trailers with different connectors and all the electrics on each trailer works. I mounted mine directly to the receiver hitch frame. The biggest challenge for us was routing the backup wire from the taillight housing, through the body of the truck to the connector. the rest went together fairly easily. Seems to be pretty solid and looks much better than the loose pigtail connector it replaced.
# 9
25 Ft 5-Way Trailer Wiring Harness - Wishbone Style - 30" Ground - 5' Auxiliary Wire
So, I converted my brand new Loadrite trailer to LED'S and wanted to add up a reverse light. I purchased this 5 wires trailer light harness to do the trick. Very good quality and the color code stayed the same. Had no problem what so ever and was an easy swap. I soldered every wires and protect them with heat shrink tubing and that should last a very long time. Thank you.
Very bad experience. Placed an order on 5-24-23 for an item that showed to be in stock on the website. Receive an email stating that is back ordered and due to ship 6-5-23, several emails later still no wiring harness. Finally 7-10-23 I receive an empty envelope, well not completely empty it has a letter from USPS stating that the enclosed was found loose in the mail. A box would have been more appropriate to ship this item, as I have been in shipping for two different companies for 38 years now. I am unable to upload pictures of the envelope, I will send them via email.
# 10
Wesbar 4-Pole Flat Connector w/ Jacketed Cable - Trailer End - 8' Long
Really quality piece. Plenty of length to connect back to the rest of my utility trailer wiring that was still in good shape since it was in an area subject to far less abuse. Nothing worse than having to fix the corroded wires in between replacing the worn out plug every few years. This should give me years maintenance free service even with the toll winter takes.
This is the 2nd one of these I have purchased. They are a good product (therefore the 2nd purchase) but have a few areas that could be improved. 1) In cold northern winters (MN -10 F), the cable gets very stiff, because of the lack of flex, my trailer connection pulled out when turning, dragged on the ground and ground down the plug. 2) the connection where the cable jacket meets the plug separated (again, due to cold weather?). Even though I would prefer a more temperature-forgiving flexible cable, I believe this design is better than the other 4-flat trailer-end wiring harnesses currently available. I also purchased a Hopkins Endurance Quick-Fix Replacement 4-Way Flat Trailer Connector w LED Test Lights - Trailer End to as a quick fix to this cable to temporarily fix my trailer wiring until permanent repairs can be done.
# 11
Hopkins Endurance 4-Way Flat Trailer Wiring Harness - 20' Long
I used this harness to rewire a 10ft vintage RV. There was plenty of length to reach the rear lights. I used Scotch Locks to tap into the wiring for the side running lights. Very good product.
Very happy with every aspect of my order. Received product and quality appears to be outstanding. I’m especially impressed at the instructions made available to install the wiring harness, written with the product and link for video. All bases covered and follow up to make sure all goes well. Am confident of their assistance should I need it.
# 12
Hopkins Endurance Easy-Pull 4-Way Flat Connector w/ 48" Harness and LED Tester
Very strong wire on the connector. Finger hole access is priceless!
easy installation, I like the indicator,
# 13
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
Sooo, bought another one to match my truck side connection as GM uses Pollak, which are known to not play well with other brands. The design is just a wire clamp to wire it, which I did with the first one, but trying to get it secured I stripped out the screw. There are no torque specs provided. I’ll move to crimped ring terminals on this one and dial back the torque a bit.
Used as a replacement for original connector that didn't have a positive fit. This one clicks in and provides confidence of a snug fit.
# 14
Hopkins Wiring Harness with 4-Pole Flat Trailer Connector - Trailer End - 4' Long
Perfect! extra long so I got rid of all my bull crab wiring
This replaced a old plug.
# 15
Pollak 5-Pole, Round Pin Trailer Wiring Socket, Concealed Terminals - Chrome - Vehicle End
The pins were too big by a little bit. Had to force the female plug into the socket
Nice product. Proper di-cast with chrome finish...not the cheapy plastic one this replaced. I prefer this to the flat-4 plug, because the flat-4 can't really be secured the the vehicle, and most of the time thay are run out the truck over the bumper. I didn't want to risk scuffing the painted bumper cover, plus I have a 3rd brake light on my trailer, which requires a dedicated brake light wire. I installed this on a 2006 WRX and a 1990 Mustang (1 trailer, 2 cars that tow it)
# 16
Pollak 6-Pole, Round Pin, Trailer Wiring Connector - Trailer End
Quick shipping, will order from them again!
Exactly what I needed and It's a great fit
# 17
Hopkins Tail Light Converter with 4-Way Flat Trailer Connector
I used the Hopkins 3 to 2 converter to make a 6-pin round to 4-flat connector for my Winnebago View motorhome. While there are 6-4 plugs available to do this, they do not work on the Winnebago View (no brake lights). This adaptor works great.
This device was no help in connecting my five wire trailer to my four wire goldwing. I ended up having to use a number of diodes in the trailer wiring to make everything work properly. My trailer had red LEDs that were used for Brake, Turn & stop and I had to get the brake and turn function to share the same lead on the light fixture.
What our customers are saying:
"In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!"