Plate allows you to mount your bike carrier or other rooftop accessories to your Exposed Racks multifunctional crossbars. Mounts parallel to crossbar using push-pin system. 1/4" Bolt channel width.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everyone, I'm Ellen here at etrailer.com, and we're going to be taking a quick look at the Exposed Racks accessory mounting plate. This can attach into any of the square holes on your Exposed Racks. It does go in this parallel configuration, so it's going to run along with the bar, but you can use this to make it quick and easy to attach any of your accessories, like a bike rack, or a cargo carrier, or any other kind of rooftop-mounted accessory that you want. So it makes it easy to kind of mix and match and make the most out of that Exposed Racks. So, you can have all your accessories mounted up there.So let's take a closer look at it and see how this installs, and what it can do for you. So as I mentioned, it does attach in parallel with that bar so it just goes right along with it.
The way it attaches is just these two D10s. So you can see coming down here through the bottom. So, push those in and lift up to remove it and just as easy to put this in place as well. It's a little bit quirky just on my table because it's not attached to a roof so it's just resting on that bar, but if you just push those D10s in and then push this guy down through, and you're just going to push it all the way down until those come out the bottom. So really easy to get that installed.Along the top of it we'll have these slots to Mount in your accessories and it comes with the hardware to attach those.
It'd be four carriage bolts, and then we'll also have our flat washer, lock washer and nut to go with each of those. So you can use that to attach on your hardware, not necessarily with the bolt going out like this, I'm just doing that to show you the other pieces, but just depends on what you're attaching more than likely though you're probably going to put the other way.The hardware is going to be stainless steel, so you don't have to worry about this causing any rust, discoloration. The rack itself is a carbon steel, so very durable. Construction, there's a couple of silicone grommets on the bottom side of that attachment points that helps to lock it into place and make sure that it doesn't really have any wiggle. It squishes down and then provides a really nice tight snug fit.
So no worries about it rattling around on you.Yeah, this can work with a lot of different things, helps to get a lot of different accessories mounted up. As far as the overall measurements, it's just about 16-inches long. And then about three-inches wide sticks up from the top of our bar by about seven-eighths of an inch. So we're just increasing the overall height of our bar by a little bit, excuse me. And then each of our slots we'll have three different ones to choose from.
And those are spaced apart by about an inch. So, that's about how far of an adjustment you have between all of those. And there're different slots to attach in your other accessories. It is made in USA. The channel width is an inch or a quarter inch, and then it is covered by a three-year limited warranty.Well, I hope this has been helpful in deciding if this is going to be the right accessory for you. You can get a bunch of these and really mix and match as you want to attach any of those accessories and then make it easy to remove them. If you don't want to have them upper up there all the time. So maybe if you want to have a bike rack on there sometimes, but you want a quick way to remove it. You can just use that D10 to pull it off and it makes it really easy. So hope this has been helpful. And thanks for watching..
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
Plate allows you to mount your bike carrier or other rooftop accessories to your Exposed Racks multifunctional crossbars. Mounts parallel to crossbar using push-pin system. 1/4" Bolt channel width.Review from a similar Perp Accessory Mounting Plate in Accessories and Parts
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.