Will the SnapPad Jack Stand Pads Work With Steady Fast or JT Strong Arm Stabilizer

Question

Question:

I have the Steady Fast Stabilizer bars attached to the landing feet of my 5th wheel? Will these bars interfere with the installation of the snappads.?

asked by: Ricky

1

Helpful Expert Reply:

The SnapPad Jack Stand Pads like part # SP54FR4 may still work with the Steady Fast or JT Strong Arm Stabilizers but you'd likely need to trim the pad where the arm attaches or raise the arm up a bit from the pads. There is a lip on the pads that will sit above the feet.

expert reply by: Conner L

1

click to enlarge

Answer 1

The Telesteps 7' Folding Ladder #TE27FR is 70" from the top rung to the ground. Each step is 11-3/4" from rung to rung. It is also very light weight as it only weighs 24-1/2 pounds. The Telesteps 10' Telescopic A-Frame Ladder…

view full answer...

Answer 2

You should be able to get the nylon bushings out fairly easily. In the worst case scenario, you can use an old 5/8 inch bolt or piece of round bar stock and punch the bushing out. The bronze bushings can be pounded in with a mallet or a hammer. If…

view full answer...

Answer 3

We do have the bronze bushings, #D014-077-00, and wet bolts, #126B2, to use with the Equa-Flex Equalizer. Or combine the bushings, wet bolts, and 1/2 inch shackle straps with #K71-358-00. Yes, the main bolt that attaches the Equa-Flex to the hanger…

view full answer...

Answer 4

The Step Wet Bolt for 1-3/4" Double Eye Springs #34007-187-00 you were looking at have a usable length of 2-1/4", which it sounds like match your existing bolts and would be typical for 1-3/4" wide springs. You will need a 7/16"…

view full answer...

Answer 5

You should indeed use bronze bushings along with the Lippert equalizer kit you mentioned, which is the following part: - Lippert Tandem Axle Equa-Flex AP Kit - Wet Bolts - 3-1/8" Long Shackles #LC64FR For a quantity of four bronze bushings with…

view full answer...

Answer 6

The Lippert Equaflex equalizers with the part #LC64FR does not come with bushings so for a bronze bushing you could then use the part #D014-077-00 and you'd be set.

view full answer...

Answer 7

The shackle straps included in the Lippert Tandem Axle Equa-Flex AP Kit - Wet Bolts - 3-1/8" Long Shackles #LC64FR you mentioned are 3-1/8" center to center and 4-3/8" overall length as shown in included diagram. Using the longer…

view full answer...

Answer 8

The Wet Equalizer Bolt with Locknut and Grease Zerk #126B2 and Bronze Bushing #D014-077-00 can be used to replace the wet bolts that are frozen on your 2020 Grand Design Momentum 351M. The wet bolts on the Momentum were most likely not serviced…

view full answer...

Answer 9

Yes, If you have the the Equa-Flex system already installed on your 2015 KZ Durango Gold with 7000#axle, the Lippert Tandem Axle Equa-Flex W/ Wet Bolts - 3-1/8" Long Shackles #LC64FR are a great choice; this will work as long as they match…

view full answer...

Answer 10

The bearing kit #BK3-210 that you mentioned is specifically for 7,000lb axles. For your 2020 Grand Design Reflection 320MKS fifth wheel with Dexter 6,000lb axles, the correct bearing kit will be either #BK3-100 or #BK3-110. #BK3-100 uses a seal with…

view full answer...

Answer 11

Hey Guy, yes you can replace the base of your current Companion hitch with the slider base part #BWRVB3775 and you'd have a slider hitch that fits the OEM pucks of your 2022 Chevy Silverado 2500 short bed. Something else you might consider is…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Will the SnapPad Jack Stand Pads Work With Steady Fast or JT Strong Arm Stabilizer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching