Should I Have Constant 12 Volt Power On Brake Output Pin On 7-Way Connector
Question:
You answered the Nissan Owners as follows: If you are getting 12V of constant power on your brake controller output wire then you need to cut the blue wire from your Voyager about 6inch away from the controller and see if it still has constant 12V power. If it does then there is an issue with the wiring to the controller or your Adapter # 3050-P if you have the factory tow package. If there isnt constant 12V power then there is an issue with the wire from your brake controller to your 7-Way. Did you really mean to say inch If there isnt constant 12V power then there is an issue with the wire from your brake controller to your 7-Way.? I am having the same issue with my 2002 Dodge 3500. Should I be seeing the constant 12 volts on the blue wire from my Teksohsha Voyager Brake Controller? The brakes are working but are getting hot in just a short distance. I intend to readjust the brake shoes tomorrow to make sure shoes are set correctly, but need to know that the constant 12 volts on the blue brake wire is correct. I assume if it is correct, that the proportional brake is achieved by varied amperage and the load being present by having a trailer plugged into the receptacle loadsinch the circuit and the amperage load then changes color of the light from green to orange and then to red, depending upon the gain setting and the aggressiveness of the brake application on the towing vehicle?
asked by: Marvin H
Expert Reply:
No you should not have constant power on the brake output pin, the blue wire should only have power with the brake pedal depressed in the vehicle or the brake controller manual override is activated. If the blue wire has a constant 12V then it is an indication that your brake controller is bad, the red wire was installed incorrectly or there is a short in the wiring.
If this is a hard wire installation (does not use a brake controller adapter cord) then the red wire will connect to the cold side of the brake switch in the truck. If the red wire was attached to the hot side of the brake switch then your brakes will get constant power. You want the brake controller to be activated by the vehicle brakes only when the brakes are depressed. You want to attach the red wire to the wire near the brake pedal that only shows power when you press the brake.
If your red wire is attached correctly, sever the blue wire 6 inches back from the brake controller and still have 12V without the brake pedal depressed or manual override applied then the brake controller needs to be replaced. If that is the case I recommend Tekonsha Prodigy P3 # 90195 because of it's LCD display screen. It shows read outs of actual words instead of troubleshooting codes that can be hard to decipher so it is much more convenient in stressful troubleshooting situations in the future.
If the blue wire only shows 12V when the brake pedal is depressed or the manual override is applied then the issue is somewhere between the brake controller and the 7-way plug, not the brake controller itself.
Go ahead and reconnect the blue wire to the brake controller and inspect the 7-way plug. You want to check the 7-way plug for any bent pins or corrosion on the pins that could be causing a short on the brake output pin. If you see signs of corrosion you can sand it off with a fine grit sand paper.
You can use the circuit tester to test the brake output pin on the 7-way for constant power without the brake pedal or manual override applied. If you have constant power there then you want to check to trace the blue wire from the 7-Way up the vehicle for damage or exposed sections of wire.
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- LCD Display
- Multiple Trailers
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Trailer Wiring
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Shop: Redarc Tow-Pro Elite Brake Controller w/ Custom Harness - Dash Knob - Off-Road Mode - Up to 3 Axles
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Custom Harness - Dash Knob - Up to 2 Axles - Proportional
- Shop: Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: pull pin
- Q&A: How to Test Electric Trailer Brake Magnets to Determine if They Need to be Replaced
- Shop: UWS Deep Low Profile Truck Bed Toolbox - Narrow Crossover - Slim Line - 6.1 cu ft - Gloss Black
- Q&A: Replacement Air Conditioner for RV Duo Therm 57915.531
- Q&A: Which Pin On A 7-Way Should Have Constant 12V Power When Vehicle Is Running
- Search Results: 3035p
- Q&A: How do I Tell if the Brake Controller is Bad
- Search Results: brake controller
- Video: Detailed Breakdown of the Trimax Puck Lock for Trailer Door Hasps
- Video: A Closer Look at the Trimax Puck Lock for Trailer Door Hasps
- Q&A: Brake Controller Has Constant 12V Power But Trailer Brakes Do Not Engage
- Shop: Vehicle Tow Bar Wiring
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Video: An In-Depth Look at the Curt Echo Wireless Brake Controller
- Video: How to Install: Curt Echo Wireless Brake Controller on your 2020 Subaru Outback Wagon
- Article: Troubleshooting Brake Controller Installations
- Q&A: Troubleshooting Brakes Sticking With Dexter DX Series Electric Over Hydraulic Actuator K71-650
- Search Results: redarc mounting panel
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Video: Installation: T-One Vehicle Wiring Harness with 7-Way Trailer Connector on a 2022 Nissan Frontier
on Trailer Brake Controller
