Hand Brake Recommendation for Timbren Axle Less System
Question:
i was wondering for the ASR35HDS02 is there a drum brake with a hand parking brake that would work with the Timbren Axle-less. What other products would i need to make the hand parking brake work? Thank you
asked by: Ham
Expert Reply:
To use a hand brake like the part # T2385200 with the Timbren system part # ASR35HDS02 that you referenced you will need to use a hydraulic drum brake with a parking brake linkage.
Since the recommended hub/drum is the part # 8-201-9UC3-EZ which is a 12 by 2 inch drum the correct left hand brake assembly would be the # T2351300 and the right hand side would be # T2351200.
I also attached a help article on adding hydraulic drum brakes to a trailer for you to check out as well.
Products Referenced in This Question
Dexter Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 6 on 5-1/2 - Pre Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Pre-Greased
- 25580 / 15123
- Standard Grade
- For 5200 lbs Axles
- For 6000 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Dexter Uni-Servo Hydraulic Trailer Brake Assembly w/ Parking Brake Lever - 12" - Right Hand
- Accessories and Parts
- Trailer Brakes
- Hydraulic Drum Brakes
- RH
- 7000 lbs
- Brake Assembly
- Single Servo
- 12 x 2 Inch Drum
- Dexter
more information >
Dexter Uni-Servo Hydraulic Trailer Brake Assembly w/ Parking Brake Lever - 12" - Left Hand
- Accessories and Parts
- Trailer Brakes
- Hydraulic Drum Brakes
- LH
- 7000 lbs
- Brake Assembly
- Single Servo
- 12 x 2 Inch Drum
- Dexter
more information >
Dexter Parking Brake Kit with Breakaway for Hydraulic Drum Brakes
- Accessories and Parts
- Trailer Brakes
- Hydraulic Drum Brakes
- Breakaway Kit
- Parking Brake
- Dexter
more information >
Product Page this Question was Asked From
Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle - 4" Lift - 5 Bolt - 3.5K
- Trailer Axles
- Rubber Spring Suspension
- Standard Grade
- No Hubs
- 3500 lbs
- Spindles Only
- Universal Fit
- Lift - 4 Inch
- Timbren
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Timbren Axle-Less System for a Livin' Light QuickSilver 10.0 Pop-Up Camper
- Q&A: Axle Needed For An Off-Road Utility Trailer With 40x13.50 Tires And A 8x170 Wheel Bolt Pattern
- Q&A: Recommended Hubs and Brakes to Build Offroad Trailer with Timbren Axle-Less Trailer Suspension
- Q&A: Trailer Hub Compatibility with 17 Inch Wheels
- Q&A: Can a Hub with Outer Bearing 15123 and LM67048 Both Fit Same Spindle
- Q&A: Availability Of Hub/Drum Kit With Brakes And Hardware Similar To Part BPH1206EPR
- Q&A: Can Timbren Axle-Less System be Used with 17" Wheels for Off-Road Application
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: Trailer Wiring Diagrams
- Article: Trailer Tire Sizing
- Article: Trailer Lighting Requirements
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Best RV Roof Vents