Result: surface mount reverse light

Low voltage on your vehicle reverse light circuit could be caused by damaged wire, a short against | backup light only shows 7 volts not 12 what is the problem. If there is a problem where would it be ? | Low...

as an additional 12V power source. The second is as a reverse light wire if the trailer is equipped with reverse | hi i saw a posting regarding this but wanted to confirm before i order. my...

at your lights, ensuring they are good and are attached to bare metal surfaces and free of any paint, dirt | I’ve been using my trailer and vehicle combo for over two years but it was pointed out the last time...

to the connection point at the rear of your truck for trailer brakes, trailer reverse lights, and an accessory 12V | My 2007 tundra came with just a 4 way flat connector. They tell me the plugs are up under...

I can help you add reverse lights to your trailer. Yes, It is important to pay attention to DOT | I have a Boat Trailer that I would like to add a pair of Backup Lights to assist while backing my boat up in...

bare metal surface on the vehicle. You can connect the purple wire to the reverse light circuit behind | Id like to install the Pollak HM40975 7/4 pole on my 2011 Ford Transit Connect. What...

and dirt can become trapped inside the gap between the trailer surface and the jack's round mounting flange | The lights work but jack wont, we heard a click but doesnt go up or down! He checked the ground...

wire from the brake controller and the purple wire is used to attach to the reverse light circuit | Hello, I have a 2014 GMC Savana 3500 with the 6.6L Diesel. It came from the factory with no tow package and...

connector to include back-up lights to power the reverse solenoid on my trailer surge brakes. Can you help | Greetings, I’m looking for a trailer harness for a 2011 Honda Pilot. However, I need a 5 pole connector...

. The connector on the vehicle should have a ground wire secured tightly to a clean surface on the frame. A wire | Turn signals work and no break lights. Hopkins plug and play on a 2015 jeep Wrangler. What do I look for. Mike...

(reverse light pin) on your Ford's 7-way being corroded, so you can either clean it or replace | Just bought a new boat, the trailer has a surge brake on it. When I put the trailer in reverse the surge brake...

for a ground. The blue wire will go to your brake controller. The purple wire is used for reverse lights | How can I convert this so it works properly. I have a 1998 ford ranger and it has a 4-way round connector....

. If the lights ground via the mounting hardware then remove the lights, sand down the surface, and then reattach | Both indicators come on when I turn right or ingage the the...

. The blue is attached to the blue wire from a brake controller. The purple wire is used as a reverse light | Hello, Do you have a 7-way wiring for 1997 Toyota 4Runner? Thanks. | We have just what you are...

the bottom of the jack plate and the mating surface on the trailer. Removing the paint, primer, rust or dirt | Hitch is stuck up and will not lower. Button is getting power | Electric tongue jacks like the 5000 lb-rated Stromberg...

. There is no special adapter to wire a light strip to your truck's reverse lights. That would require splicing | I just bought a 2015 GMC Canyon SLE Z71 with both a 7- and a 4-pole trailer...

plate and the mating surface on the trailer are making bare metal-to-metal contact. Sanding both | My Husky 4500R stopped! Lights work but the motor will not lift or retract the leg. It is not binding or attempting to raise...

of the jack mounting plate and the top of the trailer mounting surface. You want to expose clean bare metal | Electric jack won’t extend or retract but light works | Your power issue could...

tent trailer that I have. I would like it to be round tailights, LEDs, surface mount, with side | Good afternoon. I really hope you can help me. I am looking for a trailer light kit for a small tent trailer...

bare metal surfaces from future corrosion. The lights on jacks are usually high-efficiency LED types | Hi jack will not work fuse is good replaced the switch no power but the light works. ...

with the trailer frame. Grounds must be made to clean bare metal, a surface free of paint, primer, grease, rust | I have a trailer that has a 4 way plug on it. The right side light is the only one that wants to work. But when...

tail light, sand down the mounting surface, and then reattach. If the light grounds though a single | The trailer tail lights work as it should along with the righthand indicator...

. When the camper is plugged into the tow vehicle 2013 i think suburban, the reverse light come on. I | 2008 jayco camp trailer, right tail lamp, brake, signal does not work. All other lights work. When the...

Connecting the 12V power, electric brake output, and reverse functions will not fix the running | I have a 2010 ford F-150 pickup which has a 4-flat trailer hookup. just purchased a popup camper with a 7-way plug. I purchased...