Result:

This brake controller has a few different mounting options if you don't want to just drill a hole through the dash for it to sit in: # 331-TPSI-002 # 331-TPSI-001 # 331-TPSI-007 For the back up camera I recommend the Rear View Safety G-Series Backup Camera System # RVS-776718-D. |

That covers the LED and the batteries which leaves us with a rear camera such as the Rear View Safety Backup Camera System # RVS-770613-213....

For a back up camera and monitor you will want the Rear View Safety Backup Camera System - Mirror Monitor - License Plate Mounted Camera item # RVS-778718N. |

I have included a link to a video review of this camera system for you. | Im thinking of buying 2 of the HM50002 for my 03 ford focus, one for the rear just for backing up dark tinted windows so I can see, and...

| The VueSMART RV and Trailer Backup Camera part # HM34FR does require the running light circuit for activation. | With the LED lights on the back of my cargo trailer with the tailgate ramp how would you hook...

If the camera mounting bracket you have on the rear of your camper is from Furrion then you can use the Furrion RV Observation Camera System w/ Monitor and Bracket part # FOS43TASF. |

You should also use a weight distribution hitch like the Equal-i-zer Weight Distribution System # EQ37060ET. This will help to distribute the tongue weight of the Bambi across your Telluride so you do not experience rear sag which causes light steering and diminished braking. |

I have attached the installation manual for the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling 4-Point System # LC358590 below. It is the same instructions for the 6-Point # LC675817 kit. | I see...

Hello, I have a unique wiring problem that Im trying to work out for my towed RV. In addition to the two existing Stop/Turn/Tail lights, I want to add a third brake light to the rear of my towed RV. |

Note: Ive constructed a frame-supported rear cargo box and bike carrier unit that extents about 4foot beyond the rear bumper - I plan to extend the STOP/TURN/TAIL lighting to the back of this unit. | Hi, Firstly,...

With modern vehicles assistance systems, is it better to source the brake input for the brake controller to come from a rear brake lamp source, as in from the rear? | I am getting a 2022 Toyota...

The Roadmaster Tow Bar Wiring Harness Part # RM-154 requires that you locate holes through which you can pass the 4-pole RV connector wiring. It is usually possible to locate rubber grommets that already have wiring passing through them if you remove carpet and trim panels in the rear of the vehicle. |

Im considering wiring 2001 crv using BX8869 Blue Ox for towing by RV. I dont want to use diode system. 1st question is, using the BX8869, how is wire run from front to back - can I go interior via thru fire wall and then by what route to the rear or do I go under vehicle and by what route and then if under where do enter interior to get to tail-lights. 2nd question is I have a blue ox cable harness with a 6 pole round plug on the end to connect to tow vehicle, how do I covert to that from a 4 way flat or can I remove the 4 way flat and connect direct to the 6 way round. |

which parts # can i use to connect 7 way RV type connector on camper with BRAKES? My SUV already has a 4 pole wiring system installed. | which parts # can i use to connect 7 way RV type connector on camper...

I recommend the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7. This kit will require running a power line from the battery, installing a few circuit breakers, and routing a brake wire from the front to the rear of the vehicle. |

Many years ago I worked in the RV field and understand vehicle and trailer wiring very well. | I have a 2012 Honda Ridgeline with a factory 7 way plug. I have a trailer that Id like to add a single LED stop warning light. Many...