!mercury  x   >   !CLK-Class  x   >   !Carpod  x   >   1972  x   >  

We are in search of a spare for our camper. The tire reads 7.00x15lt on a 17 inch rim. It is 4 bolts on 9.44. Do you have anything thing that would work with this? | Since your tires are 7.00X15LT, the "15" in that tire size means that they...

need 6000 lb hitch for 1972 c10 chevrolet. | If your 1972 Chevrolet C10 pickup has a standard bumper you will want the etrailer Trailer Hitch Receiver # e88AR. Otherwise we have the Receiver # C13099 which fit the deep drop style bumper. Both...

Hello there, Just wondering if you guys have had a chance to see if you can fit multiple extensions on the Thule Canyon in the same manner that you can make a van length roof basket with the Megawarrior and its extensions. Thanks in advance!...

whats the btu rating for the marshall brass co. model 240? I would like to upgrade to an auto change over regulator. Thank you! | The Camco Automatic Changeover part # CAM59005 will replace your marshall brass co model 240 without a problem....

I plan on using this adapter to tow a 1800 lb car, flat on 4 wheels. There would be virtually no tongue weight. Would this work ? Tow vehicle is a 2017 Subaru Outback | I do have an option that will allow for you to use your 2017 Subaru Outback...

im trying to find a hitch for my 1972 f100, i removed my rear bumper so im looking for a hitch with minimal that tucks up tight to the frame and is 34inch wide to fit the frame rails. will this hitch be safe to use for what i am talking about,?...

I have an old 1972 international scout II with a factory installed class II hitch. I have no wiring for a four pole electrical hook up. I did some searching on your website and saw that C58044 may be compatible with my Scout wiring. Is it? Do...

How long of a 5th wheel toy hauler can i pull with my Ram 3500? Single Wheels on the rear of my truck. I found a 39 ft unit im very interested in but was told i need a dually to pull it safe. Thanks for any information! | Length is not an issue...

Do you have dimensions of this spring. This is for a custom install. | I checked with Sumosprings and the # SS65FR and the dimensions are 5 inches tall by 4 inches in diameter without the spacer. |

I was thinking of using this kit on a 72 GMC p/u with a full length bed, to aid in pulling a 27 camper trailer. I estimate the tongue load 800 to 1000 lbs. Percentage wise, how far compressed would these rubbers be? | There is no way to determine...

Any hitch kit that would work for a 1972 Chevy C10 fleet side long bed. Main problem is the rear bumper was removed for cosmetics. Is there any way to still install a hitch kit without a rear bumper? | This Universal Draw-Tite Max-Frame Trailer...

Do you have a towbar Baseplate that will fit a 1972 Buick Skylark? | The best solution for your 1972 Buick Sylark would a universal base plate kit like the part# BX88230. This will bolt to your bumper. Most bumpers will need to be reinforced...

will this product fit with coils | I spoke with my contact at Timbren and she informed me that the Timbren Rear Suspension Enhancement System, # TGMRC10A, that you referenced, would work on your 1972 C/K Series with coil springs. I attached...

Do you make a trans pan cooler for the late mobel Dodge 904? If so what is the part number please? I have been looking on-line with NO luck......I have a 1972 Dodge Dat with a 318 and a 904 tranny......Thanks! | I spoke with my technical contact...

Can I install the truck receiver hitch up side down on my truck frame safely? It allows me upward additional clearance for offroading is why.And bothmy trailers are spring over axle and tall.I have inverted itfor test fit and bolt holes align....

Reduces the temp by as much as 50 degrees? If it has a thermostat, wouldnt this prevent the oil from dropping too low. Oil temp needs to stay high enough to burn out the condensation in the oil. | Typically a system like the Derale Tube-Fin...

Will this hitch fit with a step bumper ? | Yes, the Curt Trailer Hitch Receiver # 13028 will fit with the standard step bumper on your 1972 Chevrolet K10 pickup with 34" wide frame. This receiver is rated for a maximum tongue weight of 600lbs...

will the bestop soft door fit with my hardtop thanks Kent. | Yes, I checked with Bestop and the Bestop 2-Piece Soft Doors # B5177415 have been confirmed to fit your 1972 Toyota FJ40 with a hard top. I attached a set of installation instructions...

Hello, Im looking for a rain gutter roof rack for a 1972 bronco. Do you carry the Smittybilt products? thank you | If you really want the gutter mounts, we don't carry smittybuild brand, but you can use the gutter towers and then use compatible...

My 1972 Ford F250 is a Flatbed truck. Do you sell a trailer hitch for my truck? If you do I would like to buy one and everything else that goes with it. Thank you very much. | We do offer trailer hitch options for a 1972 Ford F-250 but as...

Hi, I have a 1972 Jeep renegade that I am needing a trailer hitch for. I dont know what, if any bumper came on this, but there is a flat metal frame across the back between the frame on each side that has predrilled holes in it. it looks like...

class 5, trailer hitch, 1972 F250 4x4 W/ barden bumper, spare tire access? bumper clearance? which hitch will work for me? | I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden...

I have a 1972 Chevy C20 pickup with a dealer step bumper. The bottom of the bumper is about 4.75inch below the frame 24.75inch from ground to frame, 20inch from ground to bottom of bumper, and sticks out about 9.5inch from the end of the frame. Will...

Hi, I have a 1972 Chevrolet K10 4WD truck. It has a 307 V8 engine w/ 3 speed on the column. It has leaf springs on the front and rear. It also has a standard step bumper not a bumper. I believe the shackles are 4 to 6 inches from the end...