What Wires of 4-Way to 7-Way Adapter Needs to be Connected to Use Curt Echo Mobile
My RV has a 4 post to 7 post adapter the blue black and yellow are not connected to anything will the Curt echo Bluetooth brake controller still work for me ? | You'll need to connect the black wire of your 4-way to 7-way adapter to the positive...
Any Modifications Needed To Install Curt Front Mount Trailer Hitch # 31545 On 2008 Ford Explorer
do I have to modify anything to install the above. Is it bolted on or welded.? aprox time to install by mechanic.2008 ford explorer limited model | You will not need to modify, drill, or cut anything to install the Curt Front Mount Trailer...
Brake Controller Installation on a 2008 Ford Explorer with 4-Pole Trailer Connector
I have a 2008 Ford Explorer and need a 7 pin connector and brake controller. Does a new brake controller simply plug in somewhere on the explorer? Is there an adapter to convert the 4 pin connector to the 7 pin and does this eliminate the need...
Is Trimming Required for Installation of the # 31545 Front Mount Hitch on a 2010 Ford Explorer XLT
With #31545 Curt front mount trailer hitch receiver will I have to trim any bumper parts on my 2010 explorer xlt ? Thanks | There is no drilling, cutting or modifying of any of the parts on your 2010 Ford Explorer XLT for installation of the...
TorkLift PowerArmor Locking Battery Box Dimensions- Will It Fit Patriot Power 1800 Generator
Can you fit a Patriot Power Generator 1800 into this box? If not, what box does fit this generator? | While I don't know what the dimensions on the Patriot Power Generator 1800, I can tell you that the TorkLift PowerArmor Single Locking Battery...
Noise-Reducing Wind Fairing For Thule Square Bar Roof Rack on 2010 Ford Explorer
I have a Thule 450 rack with square cross bars on my 2010 Ford Explorer. I’d like to get a wind fairing to cut down on the noise from the rack. Do you know what size or kit would work? Thanks | On your 2010 Ford Explorer Thule specifies 50-inch...
Replacement Drop Leg Needed for a RAM 2000 Series A-Frame Jack
I just purchased a camper, and the dealer did not have a footplate that would fit because of the indent on the stand itself. Can you tell me if it will fit this particular jack? It seems to have the same indent, Im just not sure if it will...
Class 3 Hitch And Towing Capacity For 2008 Ford Explorer
Bought a few things we you before and still have the brake controller. Im looking at a ford explorer with a class 2 hitch and trying to find out if it is chang to a class 3, will the explorer pull 3900 lbs. | I do carry a class 3 hitch for the...
Troubleshooting Trailer Passenger Side Stop Turn Circuit Not Functioning
I had all lights working on the trailer except for passinger rear stop lite I let friend do it now I cant get any lights on the trailer to work anybody who can help please help thank you. | First thing I would do is ask your buddy what all he...
Will the Superwinch Tiger Shark Series Off-Road Winch # SW1595200 fit Mounting Plate # SW2050
Will the superwinch model TS9500 fit this mount | Yes, the Superwinch Tiger Shark Series Off-Road Winch # SW1595200 that you referenced and the Bulldog Winch Hitch Mounted Winch Mounting Plate with Handles # BDW20011 are compatible with each...
Hitch and Motorcycle Carrier Recommendation for a 2008 Ford Explorer
I just bought both vehicles and I am looking for a way to transport it without using my utility trailer.... Any suggestions? | For your 2008 Ford Explorer the most popular hitch we offer that has been confirmed to fit your vehicle is the Curt...
Weight Distribution Recommendation for a Ford Expedition and 21 Foot Toy Hauler
I will be pulling a 21foot toyhauler with an Expedition equipped with the 9200lb heavy duty tow package. The trailer has a GVWR of 10,000 but a dry weight of 6000. With Toys, water and gear I am looking at 8300 lbs. it is my intention to not...
How to Select the Proper Ball Mount for a 2008 Ford Explorer with 1-1/4 inch Factory Receiver Hitch
What drawbar do you recommend for a 2008 Ford Explorer with a 1 1/4 factory installed receiver? Because the receiver is welded directly into the cross member, rather than under it, the location of the pin hole in the receiver does not allow...
Transmission Cooler Recommendation for Bypassing Factory Cooler of 2008 Ford Explorer
2008 ford explorer 4.6 v8 4x4 i doubt ill ever tow with it but you never know. i would like to by pass the rad. and just run a trans cooler,the rad.has leaked into the trans cooler once already.dont want that nightmare again. | It is possible...
Weld-On Exhaust Redirect Exhaust Tip For a 2008 Ford Explorer or Taurus
will this fit on my suv its a 2008 ford tarus x sel | The Weld-On Exhaust Redirect, # MF35180, is designed to fit on a tailpipe that has a 3 inch outside diameter. You will need to measure the exhaust on your 2008 Ford Explorer and/or Taurus...
Wire and Breaker Recommendation to Complete 12 volt Power Circuit on a 2006 Ford Explorer
Is a lenth of wire also needed to connect the black wire from the 7 pole connector to a 40amp circuit breaker and then to positive terminal on the Battery? I have a 2006 Ford Explorer. | The Curt Universal Wiring Kit for Trailer Brake Controllers...
Brake Controller Installation Instructions for a 2008 Ford Explorer Sport Trac with Factory 4-Way
My 08 ford sport trac has the factory tow package 4 blade. I need to add a 7 blade receiver to power my trailer brakes. Can you give me step by step instructions? Thanks. | Sure, I will be glad to help you with installation instructions for...
Could Hitch from 2000 Ford Explorer Fit 2008 Ford Explorer
I have a hitch off a 2000 ford expedition and was wondering if I can bolt that up to a 2008 ford explorer? | Those vehicles are very different so a new hitch fit would be required like the Curt part # 13112 for the 2008 Ford Explorer. |
Will the Coil SumoSprings CSS-1125R Fit a 4WD 2008 Ford Explorer?
Will these fit 4WD 2008 Explorer on the rear? | No, I am sorry Gordon they do not. The Coil SumoSprings item # CSS-1125R only fit the rear suspension on the 2WD 2008 Ford Explorers. I do not have an option or any alternative for the 4WD Explorers....
Cargo Carrier Recommendation for a 2008 Ford Explorer
We have a 2008 Ford Explorer and I was hoping to buy my husband a cargo carrier for xmas. I have no idea what to get or what I should be looking for. | The first thing you need to determine is if the Explorer has a hitch installed. If there...
Best Towing Mirror for a 2010 Ford Explorer XLT
What mirror is the best fix for a 2010 Ford explorer xlt | I would be happy to find some towing mirrors that clip onto your factory mirrors but if you are trying to replace your stock mirrors we do not offer any for your 2010 Ford Explorer XLT....
Re-wiring a European Trailer to be Compatible with a 4-Way Flat Connector on a 2008 Ford Explorer
What would be the best harness for me to splice into to adapt my 4 hole plug to a german 7 hole plug. I was looking at the 18004 but not sure if it will have everything I need for the german wiring system? | On a European 7-Way trailer connector,...
Why Must the Curt Class II Drawbar # C45014 be Used in the Rise Position Only
Why must the ball mount, #C45014, be used only in the rise position and not in the drop position? | I spoke with my contact at Curt and he said the Class II Drawbar, # C45014, has not been tested for use in the drop position. They only test...
Replacement Installation Kit for Aries Grille Guard AA3059 for Ford Explorer
Is this kit compatible with Aries Grille Guard model 3059 black or 3059-2 polished? | The Aries Grille Guard # AA3059 does fit your 2010 Ford Explorer and the appropriate Replacement Bracket and Hardware Kit is part # AABRKT-3059. Aries Replacement...
Filter Your Search
Contact and Help