Recommended Timbren Axle-less, Trailer Brakes, and Ark Articulating Coupler For Overlanding Trailer
Please quote on: 1 - 2000-2200 lbs Timbren axleless set up with Disk Brakes and 5 on 5 hubs for Overlanding use with 17 inch wheels . 1 - Trailer Brake Controller 1 - Ark Articulating off-road coupler | I would be happy to recommend some...
Axle Solution for Trailer that Will Use Wider Tires and Jeep Bolt Pattern
Dear Etrailer, I have a problem! Perhaps you have a solution? i bought a small utility trailer to pull behind my Jeep. It has what I believe to be a 56 axle, springs at 46 ?. The trailer is 4 x 6. I want to use a set of Jeep Wheels that match...
2017 Jeep Wrangler Unlimited Brake Controller Installation
I cant figure out where to connect the red wire for my 2017 Jeep wrangler unlimited with factory 7 pin harness. | The Dexter Predator DX2 Trailer Brake Controller - 1 to 2 Axles - Proportional # 58-8 will have the red wire connect to the brown...
Replacement Brakes for a Dexter 3,500 lbs Axle
I’m looking for trailer brakes for my horse trailer. I have a Dexter 3500K axle. The part number for the trailer brake is 23-026. | Thanks for the part number! We have a couple of options to replace the brakes on a Dexter 3,500 lbs axle depending...
Correct E-Z Flex Heavy Duty Rubber Suspension System for a 2005 Keystone Outback 21RS
Which are the correct E-Z Flex Equalizers for my trailer with 33inch axle spread? | The correct E-Z Flex Heavy Duty Rubber Suspension System for a 2005 Keystone Outback 21RS is going to be part # K71-652-00. |
Parts Needed to Add Brakes 2,000 lb Trailer Axle with 5 on 4-1/2 inch Bolt Pattern
I have a 4foot wide camp trailer, weight is 1200 lbs. wet. It currently has a 62inch hub face, 2000 lb. axle with idler hubs. Axle has brake backing plates. I am running 15inch tires with 5 on 4.5 pattern rims. Why cant I use electric brakes...
Recommended 6-Bolt Hub and Drum Assembly for Off-Roading Trailer
I need to know which 6 on 5-1/2 hub and drum assembly will work with the following products I have: Timbren ASR35HDS02, and Dexter Electric Trailer Brake Kit w/ Parking Brakes - 12 | You need the Easy Grease Trailer Hub and Drum Assembly #...
Brake Wiring After Installing Dexter Over-Under Conversion Kit
I reviewed the instructions and it mentioned a wiring crimp kit for reattaching the brake wiring to the harness. Is this really necessary and, if so, do you sell it? Single axle TT with 3500# axle. thanks | Dexter simply recommends reattaching...
How Tight Should Trailer Bearings Be When Installing on a Spindle
Does the inner bearing need to be pressed on? The outer bearing slips on easy, but the inner bearing appears to be a bit of an interference fit ? | Trailer bearings can fit pretty tight to the spindle, but they would not ever need to get...
Does Kenda ST235/85R16 Radial Trailer Tire with 16" Black Mod Wheel 8 on 6-1/2 have an Offset
What is the offset for this rim ? And will this work with the hubs 42866UC3-EZ? | The wheel in tire and wheel combo # AM32743B is wheel # AM20761B which has a zero offset. This means the mounting surface of the wheel is in the dead center...
Recommendation For Replacement Hubs For 2002 Coleman Cottonwood Popup Trailer
I have 2002 Coleman Cottonwood popup trailer and I’m looking to replace the hubs. The stud and nut are Seized together and can’t remove the tire. I know it’s a 7” hub and it’s a 5 lug. I’m not sure what kit to buy. Can you help me? | Normally...
Recommended Bolt On Actuator to Replace Old Atwood Drum Brake Actuator
Hello, I have 1990 TI boat trailer that has the old style Atwood drum brake actuator that is shot. I know there is no replacement parts so I need to replace the actuator. I have read that you guys recommend a titan with manual lock out. The...
Can Brakes be Added to Trenton AUT1064b Trailer
Can Trenton AUT1064b trailer be converted to accept electric brakes if not can an axle from AUT1064HD be substituted I.e. fit on aforementioned with electric brake assay. and what other alterations I.e. changes wiring fenders etc will also need...
Axle and Brake Compatibilty for a UTV Trailer
I am having a custom UTV trailer built with a 3500 pound single axle. The builder will use Dexter axles or Rockwell American axles for this build. Which axle would be the best one to use to add brakes to this later? I saw an etrailer video...
Filter Your Search
Contact and Help