Result:

Hi E-trailer support staff. I just want to make sure this kit will work with analog brake controllers, not just the R F controllers? And is it using the brake lamp signal in the 4 way connector to signal the controller to power up the...

My trailer is a 96 jayco popup that has a 6 wire plug and p/u has a 7 plug flat but cant get brake lights to work | Whenever any type of adapter like # PK12716 is used to mate different types of connectors on the vehicle and trailer, connection...

I have trailers that I need door holders. They are 16’ trailers with a side man-door and barn door rear doors. The issue I have is that there is an awning that deploys on the curb side so when the man-door is opened it would hit into the awning...

I purchased and installed the light kit for my Ford Ranger pickup. I installed it, and it worked well with a test light. The instructions say to mount the module in the trunk or a location protected from weather. Thats hard to do under the back...

I have Kwikee steps 900874 on a 96 Winnebago. The book lists a step switch 905306 rectangular magnetic surface mount. It is Normally closed to extend the steps, open when the magnet is present. Is this the correct replacement - LC379406? Thank...

Whats the measurement between the two mounting holes? | The mounting holes on the Curt Trailer Hitch Receiver # C12923 are spaced apart exactly 4.4 inches front to back, on center. Horizontally left to right the mounting holes can be spaced...

Will the Curt receiver P # E3S bolt on the Westin step bumper 66000-97200 ? | The hitch part # E-3S that you referenced would not bolt up the bottom of the Westin Bumper part # 66000-97200 without a lot of modification that I can't recommend. Instead...

I have a ranger trailer that has a bad hub. Needing a hub that has a 13/8 bearing on both ends front and back need asap! | In order to pick out the correct hub assembly for a trailer you are going to need know a few key pieces of information....

Can a 1996 Ford Ranger 5 speed manual 2WD be flat towed without disconnecting the drive shaft? If yes, could you please provide a complete list of parts I would need to do this? Thank you! | I took a look at the online owner's manual for a 1996...

Can you send me all components needed to flat tow the vehicle above. Trying to help out my wife’s cousin who is new to this. Thanks | You'll need base plates, a tow bar, safety cables, a wiring solution, a supplemental braking system and possibly...

Your bumper looks great. I want a bumper that fits my truck. 1996 ford ranger 4x4 EXT, fender wells in the bed, step. now since it is older things are rusted. It didnt pass state inspection due to behind wheels bunper has rusted through.It cost...

Hitch needed for 1996 Ford Ranger Splash 6 cyl. Hauling a 750lb motorcycle and trailer will weigh about 400 lb. what do you recommend and do you have a video showing install. | For your 1996 Ford Ranger Splash the Draw Tite hitch part # 75082...

my turn signals are seperate from my brake lights, what do I need so I can rewire my truck to my small fifthwheel trailor with electricbrakes? | First, if your 1996 Ford Ranger came with a factory 4-Way trailer connector or you installed an...

Upon watching the video for the installation, which shows a 1998 ranger, it seems that I would need to drill a hole on each side in the frame. Does that seem right? Thank you | When installing the Curt hitch part # 13138 on your 1996 Ford Ranger...

Vehicle has independent brake lights and turn signal lights. How would I go about wiring to 4pin tra | The trailer wiring kits we offer for your 1996 Ford Ranger like the Hopkins part # 40215 were designed for the type of taillights that your...

Im trying to figure out the best set up to get. I have an 95 genesis bus, and i want to flat tow my 96 4x4 manual ranger to california. Id like proportional braking, and magnetic brake and turn signals. | Hey Kevin, thanks for the information....

I have ST205/75D14 tires on my trailer is there a way of using car or truck rims and if so which make are the same bolt pattern? Thank you! | Car or truck rims do not work with trailer tires because trailer tires are made very differently than...

Should the front steering be locked | When flat towing a vehicle the steering wheel needs to be unlocked to allow the vehicle to track behind the tow vehicle around corners. |

I have a 1996 ford ranger and cannot get the lights to work. Do I need an electronic turn signal converter? | For your 1996 Ford Ranger you would need a trailer wiring harness like the part # 118325 that has a turn signal converter wired into...

1996 ford ranger xlt 4x4. can i just run the hot black wire from the plug to the hot side of battery with a fuse holder, instead of a 40 amp breaker. | You can use an in line fuse instead of a circuit breaker for the hot lead on a 7-Way. However,...

We have a 36 Fleetwood Southwind motorhome and want to tow a 1996 Ford Ranger Flare Side Short Bed. We wanted to know which parts we would need. The baseplate, tow bar, wiring for lights and the braking hookup. Could you help me with this...

SINCE THESE ARE SAE APPROVED WOULD THE KODIAK HYDRAULIC LINES BE ABLE TO BE USED ON A VEHICLE ? | Normally trailer brake lines are only used on trailers. However, if your vehicle has brake line fittings that match what the part # 18TA-BLKIT...

Your catalogue says the kit is available only for 93 and 94 Splash. It would seem the frame is the same for the Splash as the other Rangers of 1996, which are listed. My truck has no running lights and has a 5-speed manual transmission. Will...

Im wanting to buy a used hitch for my 96 ranger, and found one off a 98, will it fit our should I keep looking? | Hitch fits for the 1996 and 1998 Ford Ranger are the same as long as the 1996 Ranger is NOT the GT version. For the GT version...