!CX-9  x   >   !Sedona Travel Trailer  x   >   Yamaha  x   >  

my 2016 Nissan pathfinder has raised siderails and I want to install factory looking crossbars, what do you recommend. | The Thule Aeroblade Edge Roof Rack part # TH7503-TH7503 that you referenced has been confirmed to fit your 2016 Nissan Pathfinder...

Will this fit this ATV properly? Blogs have complained about fitting and quality of hardware. I have a superwinch ATV2000 on a 2002 Suzuki KQ300, no problems in 12 years, easy installation too. easy clean fit on 2013 Yamaha 550EPS ??? | The...

What is the length and gauge of the red power wire that is included? thanks, | The red power cable of the # DL25721 that you referenced is 25 feet long and has an 8 gauge thickness. |

Does this winch mount fit on a 2006 yamaha wolverine 450 4x4 | I spoke with my contact and they said the Bulldog Custom-Fit ATV Winch Mounting Kit, part # BDW15140, will fit the 2006 Yamaha Wolverine 450 4x4. It will also fit the 2006 to 2009...

What tire sizes will this chock accommodate? What wheel chicks do you have that will accommodate a 23” diameter tire? | A 23 inch diameter motorcycle tire would not be an issue at all for the Rack'Em Manufacturing Removable Wheel Chock # RA-17...

I got a grizzly yahama 2018 700 Eps wanting to make sure this Bulldog WInch Custom-Fit Steel ATV Winch Mount Item # BDW15185 will mount perfect. Wanting to mount Superwinch 1135220 Terra 35 3500lbs to that Bulldog WInch Custom-Fit Steel ATV...

Can you tell me what is the diameter of the inner hole of the cup? I see in the video the outer diameter of the cup itself is 1-1/2inch | Hey Toni, the inner diameter of the Replacement Mounting Cups # JIF58FR that you referenced is 1-1/2 inches...

looking on put my axles under leaf springs 28’ Enclosed trailer. dull axles | What it sounds like you are looking to do is generally called "flipping the axle" which is done with an over/under kit. There are two options available for you depending...

Can you tell me what outside diameter is of the black cable. I need to buy a rubber grommet to ensure the lack of wearing to cable. | I went to our warehouse to get the Hopkins trailer wire connector # H20046 to provide you the measurement you...

I was at the boat launch yesterday, and noticed one tire off the ground. I thought something happened to the equalizer, but after inspection it appears to be fine. There was some wood in the launch ramp I didn’t see because it was dark, and...

The wiring for the Superwinch comes up about 12 short for the winch connections. What is the best way to extend the wiring leads? They look to be about a 10 or 12ga. Installing on 2005 Yamaha Wolverine 350 FX. Solenoid has been installed in...

How do you determine the left hand mirror mount or the right side mirror mount. Is it by sitting on the atv or standing in front of the atv . | The CIPA ATV Handlebar Mirror # CM11132 actually fits both the left and right sides so you can install...

I would like to pull my 5 x 8 trailer with my yamaha viking but do not know if a wiring kit exists for trailer lights. I have looked but to no avail. Is something like this available? | You could use a universal style of trailer wiring for...

Im wondering which winch mount I need to mount on a 2002 Yamaha Kodiak. On Superwinch website they list a specific mount but it is for Kodiak 2003-up. Thanks. | For your 2002 Yamaha Kodiak the Bulldog Winch mount part # BDW15128 has been confirmed...

DL has a free wheeling version of the DL15721. It is the DL15761. Do you sell the DL15761? I would have the unit mounted to a portable aluminum base that would be chained back to the inner most D-rings of a toyhauler to bring in a 1000 lb boat...

Will this work with the superwinch terra 45? | Yes, the Superwinch Custom-Fit ATV Winch Mounting Kit # SW2202920 will work perfectly with the Superwinch Terra 45. I verified this through Superwinch's fit information. I have attached the written...

Do the side lens come with the above lens ? | Yes, the smaller side lens does come with the Replacement Tail Light and Side Marker Lens for Optronics Combination Tail Light # A16RB that you referenced. |

I have a 2002 bear single axel trailer with a 3500 lbs capacity. Is there any chance you can help me figure out what leaf spring I need? I can supply the vin if needed. | What you'll need to do is measure your current springs without the weight...

Item # SW1125220 I was looking at this part number for a winch for my atv. One picture shows a mounting bracket and was wondering if that bracket would work with my 2016 Yamaha Grizzly 700 EPS . Thank you | There is a specific winch mount...

HOW IS IT INSTALLED? DO YOU HAVE VIDEO? | We don't have an install video yet for the part # BDW15131, but I did attach a picture that shows the install instructions. It has a diagram that shows how it bolts to the Grizzly frame as well. |

I NEED A CORRECT MOUNTING PLATE FOR TERRA WINCH THE ONE I PURCHASED WAS FOR YAMAHA 550/700 AND SEEMS INCORRECT | To install the Superwinch Terra Series ATV Winch on your 2007 Yamaha Grizzly YFM 660 4x4 you need the Bulldog Winch Custom-Fit Steel...

So I did all my measurements on my trailer to use these to replace current stock ones. One question I have does it lower or raise the height of the trailer at all? The reason I ask is because my stock measurements are 6 1/4 between mounting...

Will this winch fit onto a 2007 Yamaha 450 Rhino? Do you sell the mounting plate? | Yes, you can use the Superwinch LT200 winch with your 2007 Yamaha Rhino 450 4x4. The custom mount you will need for your 2007 Yamaha 450 Rhino is the Bulldog...

I have a class I hitch - 1 11/4inch How can this cover fit both 1 1/4inch and 2 | Both San Fransisco Giants hitch covers we carry, parts # HCC2124 and # OHCC2124, are designed to fit 2 inch trailer hitch receivers only. |