What is the Difference between the Curt Hitch # C13293 and the Draw-Tite # 76023 for a 2021 Acadia?
Question:
what is the difference between the Curt C13293 and the Draw Tite 76023 for a 2021 GMC acadia?
asked by: BJ
Expert Reply:
As far as the Curt # C13293 and the Draw-Tite # 76023 for a 2021 GMC Acadia, the Curt is only compatible with non-AT4 models whiile the Draw-Tite is compatible with both AT4 and non-AT4 models. Also, the Curt has a 750 pound maximum tongue weight capacity/5,000 pound gross towing capacity while the Draw-Tite has a 675 pound max tongue weight/4,500 pound maximum gross towing capacity.
Another thing to consider is ground clearance and bumper clearance. For the Curt, it has a ground clearance of 14 inches and a bumper clearance measurement of 6 inches. The Draw-Tite has a ground clearance of 15-3/4 inches and a bumper clearance of 4-3/4 inches.
As far as a recommendation, I recommend the Draw-Tite for both AT4 and non-AT4 models because of the increased ground clearance and a shorter bumper clearance. Also, it has enough weight capacity for most uses.
If you need trailer wiring and a ball mount, I recommend the T-One Vehicle Wiring Harness for Factory Tow Package # 118720 along with the Curt Towing Starter Kit for 2" Hitches - 2" Ball # C45534.
Products Referenced in This Question
T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Vehicle End Connector
- No Converter
- Factory Tow Package
- 4 Flat
- Plug and Lead
- Plug-In
- Tekonsha
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 750 lbs TW
- 5000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 750 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 3/4" Rise, 2" Drop - 7.5K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- One Ball
- 2 Inch Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Pre-Torqued
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 4500 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Hitch for a 2023 GMC Acadia AT4
- Article: Trailer Hitch Installation Tips
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Hitch for a 2024 Chevrolet Blazer Premier?
- Q&A: Is Fascia Trimming Needed to Install Trailer Hitch on 2022 Chevy Trailblazer
- Q&A: Width Of The etrailer Trailer Hitch Receiver # e36YR
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Comparing Curt and Draw-Tite Trailer Hitches for 2020 GMC Acadia
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Article: Trailer Wiring Diagrams
- Article: Which Hitches are Made in the USA
- Article: How to Choose the Right Trailer Hitch Class
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box