Where To Cut Bumper For Curt C13410 Hitch On 2012 Subaru Outback
Updated 09/12/2025 | Published 08/29/2025 >
Question:
The installation video shows cutting the bumper fascia centered on the middle bolt hole. The instructions show cutting the fascia off center from that middle hole. It would seem centered would be the appropriate cut. Is this correct?
asked by: Timothy M
Expert Reply:
Hello Timothy, good question. As far as installing the Curt Trailer Hitch Receiver # C13410 on a 2012 Subaru Outback Wagon, that middle bolt hole SHOULD be centered right where the receiver goes. As long as this is the case, you will want to do the centered cut and not the offset cut. I am not quite sure why the Curt instructions say to offset the cut. It could be the trim panel was designed a bit differently back when their instructions were written. Just make sure that middle hole is actually centered on the bumper. If so, you will be fine to center your cutout.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: curt 13410
- Search Results: torque wrench automotive tools
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: locking hitch pin
- Video: Installation: Curt Trailer Hitch Receiver on a 2017 Subaru Outback Wagon
- Video: How to Install the Curt Trailer Hitch Receiver on a 2012 Subaru Outback Wagon
- Search Results: bump step
- Search Results: subaru hitch cover
- Search Results: hitch cover
- Q&A: Curt C13410 vs. Draw Tite 76227 Trailer Hitch Receiver for 2015 Subaru Outback
- Video: How to Install: Curt Trailer Hitch Receiver on your 2014 Subaru Outback Wagon
- Video: Installing the etrailer Trailer Hitch Receiver on your 2017 Subaru Outback Wagon
- Q&A: Tool for Adjusting Drum Brakes on Drop Axle
- Search Results: hitch pin lock
- Q&A: What is the Hitch Pin Depth on a Hitch for a 2018 Subaru Outback Wagon?
- Q&A: Will 2018 Subaru Outback Wagon OEM 1-1/4 Hitch Work with Thule EasyFold XT Bike Rack
- Shop: Curt Pin and Clip for 2" Hitches - 5/8" Diameter x 2-3/4" Span
- Q&A: Trailer Hitch Recommendation for 2017 Subaru Outback
- Video: Oris Class III Trailer Hitch Step-By-Step Install - 2026 Volvo XC90
- Shop: etrailer D-Shape Anti-Rattle Locking Hitch Pin for Benton Hitch Accessories- 2" Hitches
- Video: Checking Out the Flint Hill Goods Locking Hitch Pin for 2" and 2-1/2" Hitches
- Video: All About the Master Lock Pivot Lock Hitch Pin for 2" Hitches
- Shop: Caliber Vehicle Ramps with Wheel Chocks - 20,000 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Trailer Wiring
- Q&A: Curt VS Draw-Tite Hidden Cross Tube Trailer Hitch Receivers For a 2018 Subaru Outback
- Q&A: Differences Between Curt, Draw-Tite, and etrailer.com Trailer Hitches for 2019 Subaru Outback Wagon



Jesse M.
9/12/2025
Hey Timothy, did centering the cutout for the hitch receiver work out for your Subaru? I'm asking because it would be helpful to know for others who might be in the same situation.