How Do You Measure Wet Bolts On Highland Ridge 5th Wheel
Updated 12/15/2025 | Published 11/05/2024
Question:
How do you measure wet bolts for highland ridge 5th wheel suspension system, I need to replace a clogged bolt
asked by: Arthur S
Expert Reply:
Hello Arthur, thanks for getting in touch. To measure a wet bolt you will just need to confirm the length and diameter of the bolt. Most wet bolts are about 3" long and 9/16" diameter like the Wet Equalizer Bolt with Locknut # 126B2. You will find the dimensions of this bolt below. Please compare this to what you have and see if it is a match. If you need a different size just let me know and I am happy to look into it.
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
- Trailer Suspension Parts
- Suspension Bolts
- Camper
- Car Hauler
- Utility Trailer
- 9/16 Inch Diameter
- 2-5/16 Inch Long
- Redline
more information >
Continue Researching
- Video: Review of Lippert Trailer Bearings Races Seals Caps - Grease Seals - LC97RP
- Shop: Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers -3-1/8" Shackle Straps
- Shop: Replacement Shackle Link with Bolts for Dexter Trailer Suspension Kits
- Q&A: What Are The Bolts With Grease Fittings For The Dexter Trailer Suspension Kit Called
- Search Results: trailer brakes
- Search Results: trailer bearings races seals caps
- Search Results: grease seals
- Shop: Replacement Wet Shoulder Bolt - Equa-Flex Tandem Axle Suspension - 9/16" x 3-3/8" - Qty 1
- Shop: Lippert Grease Seals - Double Lip - ID 2.25" / OD 3.376" for 5,200-lb to 8,000-lb Axles
- Video: All About the MORryde X-Factor Crossmember for LRE, RE, or TRE Leaf Spring Suspension
- Video: An In-Depth Look at the MORryde X-Factor Crossmember for Standard Frame Hangers
- Search Results: morryde x~factor
- Search Results: trailer bearing
- Search Results: lippert trailer hubs and drums
- Search Results: lippert 134543
- Shop: Replacement Flange Nut for Dexter Trailer Suspension Kits
- Shop: Dexter Heavy-Duty Suspension Kit for Tandem-Axle Trailers - 1-3/4" Wide Double-Eye Springs
- Shop: Step Wet Bolt for 1-3/4" Double Eye Springs
- Q&A: How to Find Correct Brakes and Drums for a 5th Wheel Trailer
- Q&A: How to Find Which Trailer Brake Assembly Goes on the Left or Right Side of a Trailer
- Q&A: 2015 Palomino Sabre 36QBOK Brakes and Bearing Recommendation
- Q&A: How to Measure to Determine the Size Trailer Brakes Needed For Hydraulic Drum Replacement
- Q&A: How To Measure For The Correct Size Slide Out Actuator On A 2005 Glendale Titanium.
- Video: Review of the Lippert Replacement Hydraulic Cylinder for RV Slide-Out
- Video: Complete Breakdown of the Replacement Lippert Venture RV Slide-Out Actuator
- Video: Feature Breakdown: MORryde U-Bolts for 5,200-lb to 7,000-lb Round Trailer Axles
- Q&A: Replacing Leaf Springs And U-Bolts On A 2021 Grand Design 31MB
- Video: Review of Dexter Trailer Bearings Races Seals Caps - Triple Lip Grease Seal Kit - DX49CR
- Shop: RV Jack Pads
Jesse M.
12/15/2025
Hey Arthur, were you able to confirm the length and diameter of the wet bolt on your Highland Ridge 5th wheel? Knowing what size matched up could really help others working on the same suspension setup.