Parts Needed to Add Brake Controller to 2010 Toyota Highlander

Question

Question:

I want to wire a 2010 Highlander for a 7 pin trailer wiring with brake controller. What do you recommend?

asked by: Taylor F

0

Expert Reply:

To add a brake controller to your 2010 Highlander you will need a 4-way, 7-way upgrade kit, and the brake controller itself. I recommend the following:

-T-One Vehicle Wiring Harness # 118449 (If you do not have the factory tow package)

-Curt T-Connector Vehicle Wiring Harness # 56042 (If you have factory tow package)

-Universal Installation Kit for Trailer Brake Controller # ETBC7

-Redarc Tow-Pro Liberty Brake Controller # RED52VR

-Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-002 (Optional)

You will start by adding one of the 4-way wiring harnesses and then upgrade it to a 7-way with the # ETBC7 which comes with everything else you need. The Tow-Pro Liberty is an incredibly reliable and easy to use brake controller with a small footprint. The main unit installs behind the dash so only the knob is visible. The mounting panel will replace one of your knockout panels giving the brake controller installation an OEM look.

I have attached some installation videos below for your reference.

expert reply by: Robin H

0

Ty

4/16/2024

Thank you Robin for this explanation.

Robin H.

4/17/2024

@Ty happy to help.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey, Stephen! We got just what you need. Since you don't have a tow package, I'm not sure if you have a hitch on your 2025 Ford Ranger so I'll include one just in case. Draw-Tite Max-Frame Trailer Hitch Receiver Part #DT35PR Curt…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Parts Needed to Add Brake Controller to 2010 Toyota Highlander

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching