Weight Distribution Hitch For Boat Trailer Compatible With Surge Brakes

Question

Question:

Do you offer a hitch that is compatible with surge brakes? For my boat trailer

asked by: Rich L

0

Expert Reply:

Yes, we have the Equal-i-zer weight distribution systems which are compatible with surge brakes. I saw you were looking at the Reese Strait-Line Weight Distribution System # RP66084 with a weight capacity of 600-1,200lbs of tongue weight and a trailer up to 12,000lbs. You would most likely need the Equal-i-zer 12,000LB # EQ37120ET which is rated for 800-1,200lbs of tongue weight. Otherwise the Equal-i-zer 10,000LB # EQ37100ET is rated for 600-1,000lbs of tongue weight. Please let me know if you have a different amount of tongue weight or total trailer weight.

If your boat trailer has a straight tongue we have the Pole Tongue Adapter # EQ95-01-5950 which will allow you to use the weight distribution hitch. It fits trailer tongues 1" to 5" wide and 2" to 5" tall.

expert reply by: Bud M

0

Answer 1

They HydraPro EOH Actuator part #DH54FR that you referenced was designed to be powered by the 12 volt accessory circuit of the tow vehicle's 7-way which typically also would get ran to the trailer battery as a charge circuit for it. So as long as…

view full answer...

Answer 2

The Timbren Axle-Less Trailer Suspension w Idler Hubs #A35RS545 are going to be the closest replacement to the Dexter 69-47 torsion axle you have under your 7 x 12 Interstate Trailer. These will place the 6" off the frame and place the axle…

view full answer...

Answer 3

The Dexter DX Series #K71-651 and the Hydrastar Vented Marine #HS381-8067 are more comparable as they both have hardwire installations (just made by different manufacturers) while the Dexter BrakeRite II #T4813102 is more of a…

view full answer...

Answer 4

To move the leaf springs on your trailer to the top of your drop axle, you can use a Dexter Over-Under Conversion Kit #K71-385-00 if you have a 3 inch diameter axle or #K71-384-00 if you have a 2-3/8 inch diameter axle. These kits will only work on…

view full answer...

Answer 5

In order to add another axle to a trailer you'd need to remove/replace any and all existing suspension components such as the leaf springs, leaf spring hangers, etc. I then recommend using the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs…

view full answer...

Answer 6

Due to the front section of your trailer A-frame you will need to use a Pole-Tongue Adapter #EQ95-01-5950 that needs to be mounted between 27-32" back from the hitch ball center. You will need to check and see if this will fit with your propane…

view full answer...

Answer 7

If the actual tongue weight of your trailer exceeds the 600 pound capacity of your weight distribution system then it essentially will be as if you don't have a system hooked up at all. The spring bars won't have the strength to properly…

view full answer...

Answer 8

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Answer 9

Hey Daniel. To convert your surge brake trailer over to electric over hydraulic system you'll need the Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes item #HS481-8067. The Hydrastar item #HS481-8067 works with factory…

view full answer...

Answer 10

Hey Steve! You're already on the right track with the Pole-Tongue Adapter for Equal-i-zer Weight Distribution Systems #EQ95-01-5950. This is exactly what you need to install a WDH on your boat trailer. Go ahead and measure 27" - 32"…

view full answer...

Answer 11

I do have a recommendation as unfortunately the Friction Sway Bar #17200 is not surge brake compatible. Using a hitch like the Equal-i-zer Weight Distribution System #EQ37100ET integrates sway control into the weight distribution. Best of all it…

view full answer...

Answer 12

The Air Lift Ride Control Air Helper Spring kit, part #AL59530 is compatible with your current tire size on your Tundra. As air pressure is added to the springs, the rear height of the vehicle would increase slightly. You are correct in your…

view full answer...

Weight Distribution Hitch For Boat Trailer Compatible With Surge Brakes

Products Featured in This Question

Continue Researching