How to Set Clock of Jensen RV Stereo JWM60A

Question

Question:

Need more info on how to set clock. For old people from the start. Turn on radio? Etc.

asked by: Latrell

0

Expert Reply:

With the Jensen stereo # JWM60A powered on press and hold the hour or minute button to access the clock setup mode. The number representing the hours and minutes will flash. Keep pressing the hour and minute buttons till the correct time is shown. The settings will take after 5 seconds of no buttons being pressed.

expert reply by: Jameson C

0

Kristen

3/5/2024

how do you change the am/pm toggle?

Jameson C.

3/5/2024

@Kristen You'll need to adjust the hour setting forward or back till it swaps from AM to PM. To change the clock setting press and hold the hour or minute button till it starts flashing.

Answer 1

I am happy to help you set the clock on your Jensen Stereo part #JWM60A. If you press and hold the hour and minute button then numbers representing the hour and minutes should flash. If you see a flash then you know the stereo is in clock set up…

view full answer...

Answer 2

Reese has a gooseneck ball that fits the OEM pucks of your 2020 GMC Sierra 3500 with the part #RP23FR but this doesn't have any rise built into it. The ball you mentioned does not fit your truck.

view full answer...

Answer 3

Hey Brad, so Reese does have a gooseneck hitch ball that fits the OEM gooseneck of your 2023 GMC Sierra 2500 with the part #RP23FR but the part #RP19315 that you referenced does not fit your truck. Was there anything in particular that you liked…

view full answer...

Answer 4

Hello Joe. I have heard about this issue with the GM puck systems. What I have been told is that it is intentional so that the hitch ball does not seize up in the Prep Package. So it makes sense why your Reese Elite Series Pop-In Ball Kit for GM…

view full answer...

Answer 5

The correct gooseneck ball for the OEM hitch on your 2024 GMC Sierra 3500 is the following: - Reese Elite Series Pop-In Ball Kit for GM Underbed Gooseneck Hitch #RP23FR

view full answer...

Answer 6

Since the Rhino box only has one set of mounting bolts you'd really only be able to raise the trailer suspension like with the Correct Track tandem axle lift kit part #RR23QX or go with a lower ball like the #RP23FR like you mentioned.

view full answer...

Answer 7

The B&W Ball and Safety Chain Kit #BWGNXA2061 is taller than the Reese Elite Series Pop-In Ball Kit #RP23FR, which is only 3-7/8" from the bottom of the flange to the top of the hitch ball (see attached photo). If you're wanting to use a…

view full answer...

Answer 8

Your Furrion RV Wall Oven, #FSRD22LASS is not intended to have the glass removed from the door. Per the attached manual "clean the glass door using non-abrasive products or sponges and dry it with a soft cloth".

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

How to Set Clock of Jensen RV Stereo JWM60A

Continue Researching