What Size Is Replacement Ball Assembly for Ultra-Fab Stabilizers

Question

Question:

What size is the ball replacement for the tripod stabilizer for 5 wheel

asked by: Eric K

0

Expert Reply:

The Replacement Ball Assembly part # UF19-001057 for Ultra-Fab Gooseneck Tripod Stabilizer that can be used with the Ultra-Fab Economy 5th Wheel King Pin Tripod Stabilizer part # UF19-950500 is a 2-5/16" ball.

We also carry the Ultra-Fab Gooseneck Trailer Tripod Stabilizer part # UF19-950450 that already comes with the 2-5/16" ball.

expert reply by: Heather A

0

click to enlarge

Answer 1

Sure thing! I went out to the warehouse and measured the: -Replacement Ball Assembly for Ultra-Fab Gooseneck Tripod Stabilizer #UF19-001057, with a set of calipers #PTW80157 and measured 7 threads per inch, with a overall diameter of 1-3/32"…

view full answer...

Answer 2

I have the perfect solution for you! I recommend going with the Ultra-Fab 5th Wheel King Pin Tripod #UF19-950500 and then adding the Replacement Ball Assembly #UF19-001057. This will convert the tripod so that you can use it with the Andersen coupler…

view full answer...

Answer 3

The Replacement Ball Assembly #UF19-001057 that you referenced can be used with an Andersen Ultimate fifth wheel adapter but it has to be used with an Ultra Fab stabilizer like the #UF19-950500 since we can't guarantee it would work on an EAZ…

view full answer...

Answer 4

Since the king pin stabilizer is only a stabilizer and not actually bearing the full weight you won't actually need to match the pin weight of the trailer and could go with a lower rated (1200lb capacity) stabilizer. The difference between the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

What Size Is Replacement Ball Assembly for Ultra-Fab Stabilizers

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching