Mounting Hardware Recommendation for TracRac VanRac

Question

Question:

I see you sell the mounting brackets but dont see the hardware that holds it down on the gutter of a van, is this available

asked by: Tony

0

Expert Reply:

Sounds like you are looking for the Replacement Mounting Hardware Kit # TAHD-80931 which is the install hardware kit for the TracRac ladder rack that the # TA01-11155 fits.

expert reply by: Jameson C

0

Answer 1

I have an answer for you. From the looks of your photo, it looks like it is the Rapid Gutter Feet for Thule Crossbars - Rain Gutters TH300R. However, even though the knobs on the Rapid Gutter Feet involve a space for Thule Same-Key Lock Cores…

view full answer...

Answer 2

Yes the Replacement Gutter Foot for Thule Gutter Feet #753-0687 that you referenced does have the rubber on the bottom of it that was dipped and not a rubber sleeve.

view full answer...

Answer 3

The Replacement Gutter Foot for Thule Gutter Feet #753-0687 is not one of the high towers. Although Thule was unable to provide me with exact measurements, I can tell you these have a 5" clearance above the rain gutters.

view full answer...

Answer 4

It looks like you are trying to fit a Thule foot for a naked roof vehicle to your Jeep Wrangler which the bracket you mentioned is not designed to fit with. Instead you would need to replace the feet altogether like with the Rapid Gutter Feet part…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi Jerry, For your 2025 Kia Sorento PHEV you would need the Curt Trailer Hitch Receiver #C37RV for the trailer hitch. The right light kit for your Sorento is going to depend on a few factors. For models with the tow package, like you stated you have,…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

Hey Christian, welcome to the world of RV-ing! So in addition to the Roadmaster Nighthawk #RM-676 you're also goin to need: - A baseplate kit, like the Roadmaster Direct-Connect Base Plate Kit #RM-521453-5. These attach to the Jeep itself so you…

view full answer...

Mounting Hardware Recommendation for TracRac VanRac

Product Page this Question was Asked From

Continue Researching