Class III Hitch Fit for a Pre November 2002 Dodge Ram 1500

Question

Question:

Hi, I was looking at the curt 13320 hitch and wanted to make sure it would fit an 2002 Dodge Ram quad cab 6ft bed made on 5/02. Before I purchased. Thanks

asked by: Mike

0

Expert Reply:

Yes, the Curt Trailer Hitch Receiver part # C13320 is a confirmed fit for your 2002 Dodge Ram 1500 with the 6' bed. The hitch is designed to fit models made before November 2002. Since your truck was made in May of 2002 then this hitch will work well. The Curt Trailer Hitch is a Class III hitch with a 2" receiver tube opening.

expert reply by: Conner L

0

Answer 1

Hey William, the other similar hitch that could maybe fit is the part #13333 but that doesn't match the date you listed. The mounting holes of this are separated by 7-3/4 inches. Would that work?

view full answer...

Answer 2

Thank you for the photo; due to the beam that hangs there isn't going to be a way for discontinued hitch 13320 to install properly on your 2003 Dodge Ram 1500 because the beam will interfere. Instead you can use the Draw-Tite hitch #75135 which…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Class III Hitch Fit for a Pre November 2002 Dodge Ram 1500

Continue Researching