Dimensions of Smallest Reducer of Gen-Turi RV Generator Exhaust System

Question

Question:

need to know the pipe dimensions of the smallest reducer on Camco Gen Turi part CAM44881

asked by: Jim L

0

Expert Reply:

The smallest sleeve of the Camco Gen-Turi Transfer Kit, part # CAM44881, has an inner diameter of 1.23 inches and an outer diameter of 1.34 inches. It's 1-1/2 inches long.

This is used to move the Gen-Turi RV Generator Exhaust System, part # CAM44461, to another RV.

expert reply by: Charles S

0

Answer 1

Rubber hoses like the MB Sturgis Propane Hose #MBS84FR should never be used for any permanent gas installations. You're going to want to use copper tubing when permanently installing any gas applications.

view full answer...

Answer 2

Yes, you can use extensions with the Gen-Turi generator exhaust system #CAM44461. We carry the 18 inch extension, #CAM44872, but you could use 2 o them if needed.

view full answer...

Answer 3

The Camco Gen-Turi RV Generator Exhaust System #CAM44461 can use the Camco Suction Cup Mounts for Gen-Turi Exhaust System - Qty 2 #CAM44850 for simple mounting. This system uses slotted bushings for an integrated fit. It sounds like you also want the…

view full answer...

Answer 4

In order to ensure that the exhaust from the Camco Gen-Turi RV Generator Exhaust System #CAM44461 does not enter into your A/C, there is definitely one thing you can do to ensure it doesn't enter your system. For a guaranteed way, I recommend…

view full answer...

Answer 5

The Camco Gen-Turi RV Generator Exhaust System part #CAM44461 comes with several different adapters to fit a wide variety of exhaust pipe sizes. It will do an excellent job of reducing the noise output in addition to redirecting the exhaust gasses up…

view full answer...

Answer 6

What you are referring to is something like the Camco Gen-Turi RV Generator Exhaust System #CAM44461 which directs exhaust up above the roof line of the RV so that it doesn't affect you or any neighbors near you. It also makes the generator a…

view full answer...

Answer 7

I reached out to Camco regarding a weld-on installation of the bushings for the Gen-Turi RV Generator Exhaust System #CAM44461. According to my contact, this is a perfectly acceptable way to install the system. When possible, welding will always…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Dimensions of Smallest Reducer of Gen-Turi RV Generator Exhaust System

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching