Does Bumper Fascia of 2013 Inifiniti JX35 Need to Be Modified to Install a Hitch

Question

Question:

Do you need to make any bumper modifications to install and fit this hitch? like the Curt Model # C13126

asked by: Eric A

0

Expert Reply:

Whether you'll need to modify the bumper fascia or not will depend on which hitch you choose.

The nice thing about the Curt Class III you mentioned, part # C13126 is that the entire hitch with the exception of the receiver opening is concealed behind the vehicle bumper. According to the installation instructions, a small (1-3/8 x 2-1/2 inch) area of the underside of the bumper fascia would need to be trimmed away. I've linked you to photos showing the area that would be trimmed and how the hitch looks once installed. The trimmed area is mainly visible from under the vehicle.

The Draw-Tite Hitch Class IV hitch, part # 76031 would be more visible, because a large portion of the crossbar and the receiver opening would be exposed, but the upside of this hitch is that it would require NO trimming of the bumper fascia. This makes for a quick installation.

If you'll be using the hitch for towing purposes, you'll need the following to complete your towing set-up:

Trailer wiring harness with 4-pole trailer connector, part # C56190KIT
Ball mount, part # AMSC2
1-7/8 inch trailer ball # 19260 -or- 2 inch trailer ball, part # 63845
Pin and Clip # PC3

I've linked you to install videos showing both hitches being installed on a 2013 Pathfinder. The procedure for your JX35 would be the same.

expert reply by: Mike L

0

click to enlarge

Answer 1

When we installed the Draw Tite hitch part #76031 on a 2016 Nissan Pathfinder like yours we found that from the top of the hitch opening down to the ground measured 14 inches. So from the bottom of the hitch it would be more like 11-3/4 inches.

view full answer...

Answer 2

Yes, there is one hitch that does not require trimming of your Pathfinder's fascia. It does require trimming a tiny portion of the carbon canister shield underneath your vehicle. You will want the Draw-Tite Trailer Hitch item #76031. This hitch…

view full answer...

Answer 3

Hello Michael. In order to add a 7-way trailer connector to a 2022 Nissan Pathfinder you'll need to start with the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #TK58VR. Then from there you want to add the Universal Installation…

view full answer...

Answer 4

Yes, you will be able to still use the hands free liftgate on your 2022 Nissan Pathfinder with a hitch installed. Do note that the receiver tube itself will block some areas under your rear hatch, so you will need to preform the foot movement near…

view full answer...

Answer 5

Tekonsha does not offer us just the harness and relay from the Tekonsha kit part #TK58VR that fits your 2022 Nissan Pathfinder. The only way to get those components would be with the entire kit. This would give you a back up 4-way in case something…

view full answer...

Answer 6

Yes, we do have the Curt Trailer Hitch Receiver #C46DR which is made in the USA for your 2022 Nissan Pathfinder. Do note that while the receiver is made in the USA some of the mounting hardware may be imported. The T-One Vehicle Wiring Harness…

view full answer...

Answer 7

You need the T-One Vehicle Wiring Harness #TK58VR that includes the additional relay harness since your 2022 Nissan Pathfinder did not come with the factory tow package installed. This harness and relay we do not carry as a separate item.

view full answer...

Answer 8

We have exactly what you need as the correct trailer hitch for the 2023 Nissan Pathfinder is the Curt Trailer Hitch Receiver #C46DR.

view full answer...

Answer 9

Yes, we do have a trailer hitch for your 2022 Nissan Pathfinder. We have the Curt Trailer Hitch Receiver #C46DR. This hitch has a gross towing capacity of 6,000-lbs, and a maximum tongue weight of 900-lbs. You should consult your vehicles owner…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Does Bumper Fascia of 2013 Inifiniti JX35 Need to Be Modified to Install a Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching