Dexstar Steel Mini Mod 16x6 Inch Wheel with 8 on 6-1/2 Bolt Pattern

Question

Question:

do you have or can you get Dexstar Steel Wheels, White Dexstar part number 17-310 - 16x6 rated for 110 psi I will need four

asked by: Olen S

0

Expert Reply:

Wheel # AM20789 is the Dexstar wheel you are looking for. The 17-310 is the Dexstar part number. The only difference is that we use a different part number # AM20789. It is the exact same wheel made by Dexstar: 16x6 with 8 on 6-1/2 bolt pattern rated for 110 psi.

expert reply by: Michael H

0

Answer 1

Thanks for reaching out, Richard! Out of the linked selection we have a handful of white wheel styles to choose from, but the most popular/common are the Steel Mini Mod #AM20785 and the Steel Spoke #AM20750 so if you're looking to match what you…

view full answer...

Answer 2

From my available research, the Dexstar model 17-293 measures 16" x 6" and has a 8 on 6-1/2 bolt pattern. While we do not carry this exact model, we do have a replacement with the identical dimensions. If this is the size you need, I…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Dexstar Steel Mini Mod 16x6 Inch Wheel with 8 on 6-1/2 Bolt Pattern

Product Page this Question was Asked From

Continue Researching