If your AC is running and you trip a breaker by turning on an appliance, this soft start fixes that. It's hardwired for security and keeps your RV safe from surges. And it lets you monitor power in real time from your phone.
Replaces the worn out surge protection board in your 30 amp Active Controls ActiveStart plug-in soft start for RVs. Lets you continue to use your ActiveStart with surge protection once the old one absorbs damaging voltage surge.
If you keep tripping breakers while your AC runs, this soft start will keep your AC from drawing too much power at startup. It also protects your rig from surges, has a replaceable surge module, and supports remote firmware updates.
This SAE to alligator clamps cable connects your 12V battery to your SAE power cable. Works with any 12V accessory that has a SAE connector on its power cord.
This hitch head assembly gives you 4" of extended shank to give you extra clearance for your tailgate, spare tire, and trailer accessories for easier hookup. Replaces the hitch head for your B&W Continuum weight distribution system.
This replacement base fits your B&W Companion fifth-wheel trailer hitch. Adjustable arms have polyurethane bushings for hitch head (sold separately) to ride on, resulting in less rattle and noise.
This hitch head has a 4" extended drop to ensure a level, stable tow for your lifted truck or low-riding trailer. Replaces the hitch head for your B&W Continuum weight distribution system.
Pair this center section with a custom mounting kit (sold separately) to get a sturdy hitch for towing your gooseneck trailer. Store the removable ball upside down in the hitch when you aren't towing to get total bed access.
This oversized mounting plate covers gaps or holes when installing a Coleman-Mach digital wall thermostat. It provides a clean, finished look and works with models 9420-381 and 9420-382.
Restore connectivity between your switch panel and RV generator with this 10-foot Cummins Onan adapter harness. Designed for use with remote start/stop control panels on HGJBB, KY, and HGJAx model generators.
You're replacing your RV's thermostat and want something easy and reliable. This single-zone analog unit gives you simple heating and cooling control without digital menus.
You're swapping out your RV's AC and need a distribution box to match. Open the louvers for cool air directed straight into the cabin, or close them to push air through existing ducts. Includes a filter that pops out for a quick rinse.
You're replacing your RV's AC and need a non-ducted ceiling assembly with built-in controls. This unit adds front and rear airflow dampers, pop-out filters, and heat strip prep. Designed for Coleman-Mach systems. Other parts required.
Reduce your Coleman-Mach RV air conditioner's start-up power demand by up to 75% and ease the strain on your AC compressor. Start and run your AC smoothly without tripping breakers or overloading your generator.
You're replacing your RV's AC and need a ceiling assembly that puts you in control. This non-ducted air distribution box has built-in knobs, adjustable louvers, and a pop-out filter. Designed for Coleman-Mach systems. Other parts required.
Turn your Coleman-Mach underbunk AC unit into a true comfort system. This kit adds a thermostat, remote, ducting, vents, and hardware so you can control temps and route your airflow exactly where you need it.
You're replacing your RV's thermostat and need a digital controller that works with your Coleman-Mach single-zone system. This is the thermostat only, but you can pair it with a compatible rooftop AC and ceiling assembly to finish your setup.
Replace the worn or non-working switch panel on your Cummins Onan generator. This panel lets you start and stop your gas or LP generator from a central location and works with select HGJBB, KY, and HGJAx models.
Need a no-nonsense lug nut? This zinc-plated open-end acorn lug nut gives you a secure fit without the fuss. Built tough to resist rust and wear, it won't trap moisture and works great with longer wheel studs.
Replace a missing or damaged caliper bracket on your DeeMaxx 6K disc brake assembly. Designed for use with integral and slip-over rotors, this bracket features DeeMaxxs corrosion-resistant MAXX coating for long-lasting durability.
Secure your stainless steel brake lines with this silicone-lined clamp. The yellow silicone cushion prevents damage from vibration, while the stainless steel construction resists rust and corrosion. Fits 1/4" braided stainless steel brake lines.
This replacement caliper has all the features you've come to know and love from your current DeeMaxx brake assemblies. The Maxx coating is even better than Dacromet for superior corrosion protection. Includes stainless steel backing plates.
Need a tough, reliable connection from your actuator to the main brake lines? The non-stick polymer core locks in pressure, while braided stainless steel fends off road debris. No ballooning, no leaks, just reliable stopping power.