Front Receiver Hitch Specs:
Features:
Easily attach a variety of accessories to the front of your vehicle with this fully welded, corrosion-resistant trailer hitch receiver. Perfect for winches, spare tire carriers and more.
Installation Notes:
No drilling required for installation
Tech Tip:
Hitch is designed for vehicles with factory tow hooks.
More Information >Videos
for Front Receiver Hitch
Help Articles
for Front Receiver Hitch
Expert Answers
for Front Receiver Hitch
Hey Michael, thanks for reaching out! The EcoHitch #EH57FR sits a little higher than the Curt #C52NR so it will give you better ground clearance for your 2024 Chevy Silverado 2500. The EcoHitch is a bit more recessed into the front bumper than the…
view full answer...From our experiences the Harbor Freight trailers like yours have a hub bore that requires a cap or Bearing Buddy that measures 2.047 inches like the #BB2047 you referenced. We don't have a standard cap that fits this size so the…
view full answer...There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…
view full answer...While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846.…
view full answer...My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…
view full answer...The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…
view full answer...The factory trailer brake controller port on your 2021 Chevrolet Tahoe is located underneath the dash just to the left of the steering wheel. It will be taped to another harness so it may take a bit of looking to find. Keep in mind that if your…
view full answer...If your 2022 Chevrolet Tahoe does not have the factory tow package then the plug may not be there. If this is the case you would need to hardwire in a brake controller. If your Tahoe does have the tow package then the plug will be under the dash.…
view full answer...I do have an option for you but we have not yet gotten out hands on a 2019 Chevrolet Blazer therefore, have not had the chance to look for the brake controller wiring port either. I checked with both Tekonsha and Curt and it looks like they have…
view full answer...The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
view full answer...M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only…
view full answer...If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part…
view full answer...Filter Products (2)
Contact and Help
What our customers are saying:
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD